MCP4342-104E/ST Microchip Technology, MCP4342-104E/ST Datasheet - Page 11

• Manufacturer Part Number: MCP4342-104E/ST
• Description: IC DGTL POT QUAD 100K 14TSSOP
• Manufacturer: Microchip Technology
• Series: WiperLock™r

Specifications of MCP4342-104E/ST

• Package / Case: 14-TSSOP
• Taps: 129
• Resistance (ohms): 100K
• Number Of Circuits: 4
• Temperature Coefficient: 150 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: SPI Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Resistance In Ohms: 100K
• Number Of Pots: Quad
• Taps Per Pot: 129
• Resistance: 100 KOhms
• Wiper Memory: Non Volatile
• Buffered Wiper: Buffered
• Digital Interface: SPI
• Operating Supply Voltage: 2.7 V to 5.5 V
• Supply Current: 450 uA
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AC/DC CHARACTERISTICS (CONTINUED)
© 2009 Microchip Technology Inc.
DC Characteristics
Weak Pull-up
Current
CS Pull-up /
Pull-down
Resistance
RESET Pull-up
Resistance
Input Leakage
Current
Pin Capacitance
RAM (Wiper, TCON) Value
Value Range
TCON POR/BOR
Setting
EEPROM
Endurance
EEPROM Range
Initial NV Wiper
POR/BOR Setting
Initial EEPROM
POR/BOR Setting
EEPROM
Programming
Write Cycle Time
Power Requirements
Power Supply
Sensitivity
(MCP43X1)
Note 1:
Parameters
2:
3:
4:
5:
6:
7:
8:
9:
10: Supply current is independent of current through the resistor network.
Resistance is defined as the resistance between terminal A to terminal B.
INL and DNL are measured at V
MCP43X1 only.
MCP43X2 only, includes V
Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
This specification by design.
Non-linearity is affected by wiper resistance (R
temperature.
The MCP43X1 is externally connected to match the configurations of the MCP43X2, and then tested.
POR/BOR is not rate dependent.
C
E
R
IN
ndurance
Sym
RESET
PSS
R
t
I
, C
WC
I
PU
N
N
N
N
CS
IL
OUT
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
All parameters apply across the specified operating ranges unless noted.
V
Typical specifications represent values for V
DD
WZSE
Min
0h
0h
0h
—
—
—
—
—
—
—
—
—
-1
= +2.7V to 5.5V, 5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ devices.
W
and V
with V
0.0015
0.0015
080h
040h
000h
1FF
Typ
170
WFSE
1M
16
16
10
—
—
—
—
—
3
A
= V
.
DD
0.0035
0.0035
W
1FFh
1FFh
1FFh
Max
1.75
), which changes significantly over voltage and
10
—
—
—
—
—
and V
1
–40°C ≤ T
B
Cycles
= V
Units
%/%
%/%
hex
hex
hex
hex
hex
hex
hex
mA
ms
µA
kΩ
kΩ
µA
pF
SS
.
A
Internal V
V
CS pin, V
V
V
V
V
f
8-bit device
7-bit device
All Terminals connected
8-bit
7-bit
8-bit
7-bit
C
MCP434X/436X
≤ +125°C (extended)
DD
DD
DD
IN
IN
= 20 MHz
DD
= V
= V
= 5.5V, V
= 5.5V, V
= 5.5V, V
= 5.5V, T
DD
SS
WiperLock Technology = Off
WiperLock Technology = Off
V
V
V
V
DD
DD
A
A
DD
DD
(all pins except RESET)
(all pins) and
= 2.7V, Code = 80h
= 2.7V, Code = 40h
= 5.5V, V
pull-up, V
= 2.7V to 5.5V,
= 2.7V to 5.5V,
CS
CS
RESET
Conditions
A
= 12.5V
= 3V
= +25°C.
= 0V
CS
IHH
DS22233A-page 11
= 3V
pull-down,