AD8402ARUZ50 Analog Devices Inc, AD8402ARUZ50 Datasheet - Page 5

• Manufacturer Part Number: AD8402ARUZ50
• Description: IC POT DIG DUAL 50K 8BIT 14TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD8402ARUZ50

• Taps: 256
• Resistance (ohms): 50K
• Number Of Circuits: 2
• Temperature Coefficient: 500 ppm/°C Typical
• Memory Type: Volatile
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 14-TSSOP
• Resistance In Ohms: 50K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Parameter
DYNAMIC CHARACTERISTICS
1
2
3
4
5
6
7
8
9
10
11
Typical represents average readings at 25°C and V
Resistor position nonlinearity error R-INL is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. Parts are guaranteed monotonic. See the test circuit in Figure 38.
I
V
INL and DNL are measured at V
DNL specification limits of ±1 LSB maximum are guaranteed monotonic operating conditions. See the test circuit in Figure 37.
Resistor Terminal A, Resistor Terminal B, and Resistor Terminal W have no limitations on polarity with respect to each other.
Guaranteed by design and not subject to production test. Resistor-terminal capacitance tests are measured with 2.5 V bias on the measured terminal. The remaining
resistor terminals are left open circuit.
Measured at the Ax terminals. All Ax terminals are open-circuited in shutdown mode.
Worst-case supply current is consumed when the input logic level is at 2.4 V, a standard characteristic of CMOS logic. See Figure 28 for a plot of I
P
W
All dynamic characteristics use V
Measured at a V
AB
DISS
Bandwidth −3 dB
Total Harmonic Distortion
V
Resistor Noise Voltage
Crosstalk
= 50 μA for V
W
= V
is calculated from (I
Settling Time
DD
, wiper (V
11
DD
W
= 3 V and I
W
pin where an adjacent V
) = no connect.
DD
× V
W
DD
= 400 μA for V
W
). CMOS logic level inputs result in minimum power dissipation.
with the RDAC configured as a potentiometer divider similar to a voltage output D/A converter. V
DD
6, 10
= 5 V.
W
Symbol
BW_10 K
THD
t
e
C
DD
pin is making a full-scale voltage change.
S
NWB
T
= 5 V for the 10 kΩ versions.
W
DD
= 5 V.
Conditions
R = 10 kΩ
V
V
R
V
A
A
WB
A
= 1 V rms + 2 V dc, V
= V
= V
= 5 kΩ, f = 1 kHz, RS = 0
DD
DD
, V
, V
B
B
Rev. E | Page 5 of 32
= 0 V, ±1% error band
= 0 V
B
= 2 V dc, f = 1 kHz
Min
AD8400/AD8402/AD8403
A
= V
Typ
600
0.003
2
9
−65
DD
and V
1
B
DD
= 0 V.
Max
vs. logic voltage.
Unit
kHz
%
μs
nV/√Hz
dB