AD8403ARZ10 Analog Devices Inc, AD8403ARZ10 Datasheet - Page 13

• Manufacturer Part Number: AD8403ARZ10
• Description: IC POT DIG QUAD 10K 8BIT 24SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD8403ARZ10

• Taps: 256
• Resistance (ohms): 10K
• Number Of Circuits: 4
• Temperature Coefficient: 500 ppm/°C Typical
• Memory Type: Volatile
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (7.5mm Width)
• Resistance In Ohms: 10K
• End To End Resistance: 10kohm
• Track Taper: Linear
• No. Of Steps: 256
• Resistance Tolerance: ± 20%
• Supply Voltage Range: 2.7V To 5.5V
• Control Interface: Serial, SPI
• No. Of Pots: Quad
• Number Of Elements: 4
• # Of Taps: 256
• Resistance (max): 10KOhm
• Power Supply Requirement: Single
• Interface Type: Serial (3-Wire/SPI)
• Single Supply Voltage (typ): 3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 24
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AD8403EVAL - BOARD EVAL FOR AD8403
• Lead Free Status / Rohs Status: Compliant

Table 9. AD8403 Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
All AGND pins must be connected to DGND.
Mnemonic
AGND2
B2
A2
W2
AGND4
B4
A4
W4
DGND
SHDN
CS
SDI
SDO
CLK
RS
V
AGND3
W3
A3
B3
AGND1
W1
A1
B1
DD
Description
Analog Ground 2.
Terminal B RDAC 2.
Terminal A RDAC 2.
Wiper RDAC 2, Addr = 01
Analog Ground 4.
Terminal B RDAC 4.
Terminal A RDAC 4.
Wiper RDAC 4, Addr = 11
Digital Ground.
Active Low Input. Terminal A open circuit. Shutdown controls Variable Resistor 1 through Variable Resistor 4.
Chip Select Input, Active Low. When CS returns high, data in the serial input register is decoded,
based on the address bits, and loaded into the target DAC register.
Serial Data Input.
Serial Data Output. Open drain transistor requires a pull-up resistor.
Serial Clock Input, Positive Edge Triggered.
Active Low Reset to Midscale. Sets RDAC registers to 80
Positive Power Supply. Specified for operation at both 3 V and 5 V.
Analog Ground 3.
Wiper RDAC 3, Addr = 10
Terminal A RDAC 3.
Terminal B RDAC 3.
Analog Ground 1.
Wiper RDAC 1, Addr = 00
Terminal A RDAC 1.
Terminal B RDAC 1.
1
1
1
1
1
2
2
2
2
.
.
.
.
Rev. E | Page 13 of 32
H
.
AD8400/AD8402/AD8403