CAT5114LI-10-G ON Semiconductor, CAT5114LI-10-G Datasheet

no-image

CAT5114LI-10-G

Manufacturer Part Number
CAT5114LI-10-G
Description
IC POT DGTL 32TAP 8-DIP
Manufacturer
ON Semiconductor
Datasheet

Specifications of CAT5114LI-10-G

Taps
32
Resistance (ohms)
10K
Number Of Circuits
1
Temperature Coefficient
300 ppm/°C Typical
Memory Type
Non-Volatile
Interface
Up/Down
Voltage - Supply
2.5 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
Resistance In Ohms
10K
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CAT5114LI-10-G
Manufacturer:
ON Semiconductor
Quantity:
191
CAT5114
32-Tap Digitally Program-
mable Potentiometer (DPPt)
Description
(DPPt) designed as an electronic replacement for mechanical
potentiometers and trim pots. Ideal for automated adjustments on high
volume production lines, they are also well suited for applications
where equipment requiring periodic adjustment is either difficult to
access or located in a hazardous or remote environment.
between two terminals R
that are controlled by three input pins, determines which tap is
connected to the wiper, R
memory, is not lost when the device is powered down and is
automatically reinstated when power is returned. The wiper can be
adjusted to test new system values without affecting the stored setting.
Wiper−control of the CAT5114 is accomplished with three input
control pins, CS, U/D, and INC. The INC input increments the wiper
in the direction which is determined by the logic state of the U/D input.
The CS input is used to select the device and also store the wiper
position prior to power down.
three−terminal resistive divider or as a two−terminal variable resistor.
DPPs bring variability and programmability to a wide variety of
applications including control, parameter adjustments, and signal
processing.
Features
Applications
© Semiconductor Components Industries, LLC, 2011
April, 2011 − Rev. 19
The CAT5114 is a single digitally programmable potentiometer
The CAT5114 contains a 32−tap series resistor array connected
The digitally programmable potentiometer can be used as a
2 x 3 mm TDFN Packages
Compliant
32−position Linear Taper Potentiometer
Non−volatile EEPROM Wiper Storage
Low Standby Current
Single Supply Operation: 2.5 V − 6.0 V
Increment Up/Down Serial Interface
Resistance Values: 10 kW, 50 kW and 100 kW
Available in PDIP, SOIC, TSSOP, MSOP and Space Saving
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Automated Product Calibration
Remote Control Adjustments
Offset, Gain and Zero Control
Tamper−proof Calibrations
Contrast, Brightness and Volume Controls
Motor Controls and Feedback Systems
Programmable Analog Functions
H
W
and R
. The wiper setting, stored in nonvolatile
L
. An up/down counter and decoder
1
See detailed ordering and shipping information in the package
dimensions section on page 14 of this data sheet.
CASE 646AA
V
CASE 751BD
INC
U/D
CS
CC
V SUFFIX
L SUFFIX
ORDERING INFORMATION
SOIC−8
PDIP−8
GND
PIN CONFIGURATIONS
INC
U/D
GND
R
INC
U/D
http://onsemi.com
R
H
1
PDIP (L), SOIC (V),
H
CASE 511AK
VP2 SUFFIX
TDFN (VP2)
1
(Top Views)
TSSOP (Y)
MSOP (Z)
1
TDFN−8
Publication Order Number:
CASE 846AD
CASE 948AL
TSSOP−8
Y SUFFIX
Z SUFFIX
MSOP−8
V
CS
R
R
CC
L
WB
V
CS
R
R
CC
L
WB
R
R
GND
R
CAT5114/D
L
WB
H

Related parts for CAT5114LI-10-G

CAT5114LI-10-G Summary of contents

Page 1

CAT5114 32-Tap Digitally Program- mable Potentiometer (DPPt) Description The CAT5114 is a single digitally programmable potentiometer (DPPt) designed as an electronic replacement for mechanical potentiometers and trim pots. Ideal for automated adjustments on high volume production lines, they are also ...

Page 2

PDIP SOIC RL4B CAT5114VT CAT5114LT YMXXXX YMXXXX R = Resistance 100 Assembly Location 4 = Lead Finish − NiPdAu B = Product Revision (Fixed as “B”) CAT5114L ...

Page 3

Table 1. PIN DESCRIPTIONS Name Function INC Increment Control U/D Up/Down Control R Potentiometer High Terminal H GND Ground R Wiper Terminal W R Potentiometer Low Terminal L CS Chip Select V Supply Voltage CC Pin Function INC: Increment Control ...

Page 4

Table 2. OPERATION MODES INC CS U/D High to Low Low High High to Low Low Low High Low to High Low Low to High X High Table 3. ABSOLUTE MAXIMUM RATINGS Parameters Supply Voltage V to GND CC Inputs ...

Page 5

Table 5. DC ELECTRICAL CHARACTERISTICS Symbol Parameter POWER SUPPLY V Operating Voltage Range CC I Supply Current (Increment) CC1 I Supply Current (Write) CC2 I (Note 4) Supply Current (Standby) SB1 LOGIC INPUTS I Input Leakage Current IH I Input ...

Page 6

Table 6. AC TEST CONDITIONS V Range CC Input Pulse Levels Input Rise and Fall Times Input Reference Levels Table 7. AC OPERATING CHARACTERISTICS Symbol Parameter INC Setup CI t U/D to INC Setup DI t U/D ...

Page 7

Applications (− – DPP – CAT5113/5114 (+) ...

Page 8

C 1 0.001 0.001 DPP 7 CAT5113/5114 4 Figure 11. Programmable Bandpass Filter +5 V IC2 74HC132 1 OSC CLO CHI ...

Page 9

PIN # 1 IDENTIFICATION D TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-001. PACKAGE DIMENSIONS PDIP−8, 300 mils CASE 646AA−01 ISSUE A SYMBOL ...

Page 10

PIN # 1 IDENTIFICATION TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD−01 ISSUE O SYMBOL ...

Page 11

E1 e TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL−01 ISSUE O SYMBOL MIN A A1 0.05 A2 ...

Page 12

E E1 TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-187. PACKAGE DIMENSIONS MSOP 8, 3x3 CASE 846AD−01 ISSUE O SYMBOL MIN A A1 ...

Page 13

D E PIN#1 INDEX AREA TOP VIEW SYMBOL MIN NOM A 0.70 0.75 A1 0.00 0.02 A2 0.45 0.55 A3 0.20 REF b 0.20 0.25 D 1.90 2.00 D2 1.30 1.40 E 2.90 3.00 E2 1.20 1.30 e 0.50 TYP ...

Page 14

... Table 8. ORDERING INFORMATION Orderable Part Numbers CAT5114LI−10−G CAT5114LI−50−G CAT5114LI−00−G CAT5114VI−10−GT3 CAT5114VI−50−GT3 CAT5114VI−00−GT3 CAT5114VP2I10GT3 (Notes 10, 11) CAT5114VP2I50GT3 (Notes 10, 11) CAT5114VP2I00GT3 (Notes 10, 11) CAT5114YI−10−GT3 CAT5114YI−50−GT3 CAT5114YI−00−GT3 CAT5114ZI− ...

Page 15

... All packages are RoHS−compliant (Lead−free, Halogen−free). 13. The standard lead finish is NiPdAu. 14. For additional package and temperature options, please contact your nearest ON Semiconductor Sales office. 15. Contact factory for package availability. 16. The device used in the above example is a CAT5114VI−10−GT3 (SOIC, Industrial Temperature, 10 kW, NiPdAu, Tape & Reel, 3,000/Reel). ...

Related keywords