SFP CONNECTOR RECEPTACLE 40POS PRESS FIT

2007492-5

Manufacturer Part Number2007492-5
DescriptionSFP CONNECTOR RECEPTACLE 40POS PRESS FIT
ManufacturerTE Connectivity
SeriesSFP+ Series
2007492-5 datasheets
 


Specifications of 2007492-5

No. Of Contacts40Connector TypeSFP+
Rohs CompliantYesProductSFP Connectors
Number Of Ports2Contact PlatingGold
Contact MaterialCopper AlloyMounting StyleThrough Hole
Termination StylePress FitAccessoryCage Assembly, 2x1 Stacked
ColorBlackFlammability RatingUL 94 V-0
Housing MaterialLiquid Crystal Polymer (LCP)Mounting AngleRight
Product TypeCageTermination TypePress-Fit
Configuration2 x 1Pcb MountSingle Sided
Termination Post Length (mm [in])3.00 [0.118]Contact Plating, Mating Area, MaterialGold or Gold Flash over Palladium Nickel
Contact Base MaterialCopper AlloyCage TypeStacked
Housing ColorBlackUl Flammability RatingUL 94V-0
Cage MaterialNickel SilverEmi ContainmentExternal Springs
LightpipeWithRohs/elv ComplianceRoHS compliant, ELV compliant
Lead Free Solder ProcessesNot relevant for lead free processRohs/elv Compliance HistoryAlways was RoHS compliant
ApplicationSFP+Lightpipe ConfigurationFour Per Column
Packaging MethodTrayLead Free Status / Rohs Status Details
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
Page 1/6

Download datasheet (66Kb)Embed
Next
Product
Specification
SFP+ Stacked Connector and Cage Assemblies
1.
SCOPE
1.1.
Content
This specification covers performance, tests and quality requirements for the Tyco Electronics Small
Form-factor Pluggable (SFP+) Stacked Connector and Cage Assemblies.
1.2.
Qualification
When tests are performed on the subject product line, procedures specified in Figure 1 shall be used.
All inspections shall be performed using the applicable inspection plan and product drawing.
1.3.
Successful qualification testing on the subject product line was completed on 12Nov09. The
Qualification Test Report number for this testing is 501-721. This documentation is on file at and
available from Engineering Practices and Standards (EPS).
2.
APPLICABLE DOCUMENTS
The following documents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the document applies. In the event of conflict between the
requirements of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirements of this specification and the referenced documents,
this specification shall take precedence.
2.1.
Tyco Electronics Document
501-721: Qualification Test Report (SFP+ Stacked Connector and Cage Assemblies)
2.2.
Industry Document
EIA-364: Electrical Connector/Socket Test Procedures Including Environmental Classifications
2.3.
Reference Document
109-197: Test Specification (AMP Test Specifications vs EIA and IEC Test Methods)
3.
REQUIREMENTS
3.1.
Design and Construction
Product shall be of the design, construction and physical dimensions specified on the applicable product
drawing.
3.2.
Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
3.3.
Ratings
Voltage: 120 volts AC
!
Current: Signal application only
!
Temperature: -55 to 105°C
!
©2009 Tyco Electronics Corporation
* Trademark
Harrisburg, PA
| Indicates change
All International Rights Reserved.
For latest revision, visit our website at www.tycoelectronics.com\documents.
For Regional Customer Service, visit our website at www.tycoelectronics.com
108-2331
19Nov09 Rev A
1 of 6
LOC B

2007492-5 Summary of contents

  • Page 1

    Product Specification SFP+ Stacked Connector and Cage Assemblies 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the Tyco Electronics Small Form-factor Pluggable (SFP+) Stacked Connector and Cage Assemblies. 1.2. Qualification When tests are performed on ...

  • Page 2

    Performance and Test Description Product is designed to meet the electrical, mechanical and environmental performance requirements specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental conditions. 3.5. Test Requirements and Procedures Summary Test ...

  • Page 3

    Test Description Transceiver insertion force. Transceiver extraction force. Rotational cable pull. Press- fit insertion force. Press-fit extraction force. Cage latch strength/module retention. Reseating. Mate/unmate. Thermal shock. Rev A Requirement 18 N [4.0 lbf] maximum. 12.5 N [2.8 lbf] maximum. 33.4 ...

  • Page 4

    Test Description Thermal disturbance. Humidity/temperature cycling. Temperature life, preconditioning. Temperature life. Mixed flowing gas. Dust. Shall meet visual requirements, show no physical damage, and meet requirements of additional NOTE tests as specified in the Product Qualification and Requalification Test Sequence ...

  • Page 5

    Product Qualification and Requalification Test Sequence Test or Examination Initial examination of product LLCR Insulation resistance Withstanding voltage Random vibration Mechanical shock Durability Transceiver insertion force Transceiver extraction force Rotational cable pull Press-fit insertion force Press-fit extraction force Cage ...

  • Page 6

    QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Specimen Selection Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Test groups and 6 shall each consist ...