LLL315R71C104MA11L Murata, LLL315R71C104MA11L Datasheet - Page 8

CAPACITOR, 100NF 16V X7R 1206 LOW ESL CAPACITOR, 100NF 16V X7R 1206 LOW ESL

LLL315R71C104MA11L

Manufacturer Part Number
LLL315R71C104MA11L
Description
CAPACITOR, 100NF 16V X7R 1206 LOW ESL CAPACITOR, 100NF 16V X7R 1206 LOW ESL
Manufacturer
Murata
Series
LLLr
Datasheet

Specifications of LLL315R71C104MA11L

Capacitance
100NF
Voltage Rating, Dc
16V
Capacitor Dielectric Type
CERAMIC MULTI-LAYER
Tolerance,
20%
Tolerance, -
20%
Temp, Op.
ROHS COMPLIANT
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
*1 : The ligure Indicates typical inspection.Please refer to individual specifications.
*2 : Some of the parts are applicable in rated voltageA150%. Please refer to individual specifications.
No.
14
15
16
17
Continued from the preceding page.
Temperature
Cycle
Humidity
(Steady
Humidity
Load
High
Temperature
Load
State)
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
D.F.
I.R.
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
No marking defects
Within T7.5% *1
W.V.: 25V min.; 0.025 max.
W.V.: 16V max.; 0.035 max. *1
More than 10,000MΩ or 500Ω · F (Whichever is smaller)
No failure
No marking defects
Within T12.5% *1
0.05 max. *1
More than 1,000MΩ or 50Ω · F (Whichever is smaller)
No marking defects
Within T12.5% *1
0.05 max. *1
More than 500MΩ or 25Ω · F *1
(Whichever is smaller)
No failure
No marking defects
Within T12.5% *1
W.V.: 25V min.; 0.04 max.
W.V.: 16V max.; 0.05 max. *1
More than 1,000MΩ or 50Ω · F *1
(Whichever is smaller)
No failure
Specifications
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10).
Perform the five cycles according to the four heat treatments
listed in the following table. Let sit for 48T4 hours at room
temperature, then measure.
• Initial measurement.
Sit the capacitor at 40T2°C and 90 to 95% humidity for 500T12
hours. Remove and let sit for 48T4 hours at room temperature,
then measure.
Apply the rated voltage at 40T2°C and 90 to 95% humidity for
500T12 hours. Remove and let sit for 48T4 hours at room
temperature, then measure. The charge/discharge current is
less than 50mA.
Apply 200% of the rated voltage for 1000T12 hours at the
maximum operating temperature T3°C. Let sit for 48T4 hours
at room temperature, then measure. The charge/discharge
current is less than 50mA.
•Initial measurement.
Specifications and Test Methods
Perform a heat treatment at 150
let sit for 48T4 hours at room temperature. Perform the initial
measurement.
Apply 200% (*2) of the rated DC voltage for one hour at the
maximum operating temperature T3°C. Remove and let sit for
48T4 hours at room temperature.
Perform initial measurement. (*1)
Temp. (°C)
Time (min.)
Step
Min. Operating
Temp.
30T3
1
+0
–3
Test Method
Temp.
Room
2 to 3
2
+0
–10
°C for one hour and then
Max. Operating
Temp.
30T3
3
+3
–0
Temp.
Room
2 to 3
4
C02E.pdf
71
05.12.14
12

Related parts for LLL315R71C104MA11L