MT8HTF12864AZ-800H1 Micron Technology Inc, MT8HTF12864AZ-800H1 Datasheet
MT8HTF12864AZ-800H1
Specifications of MT8HTF12864AZ-800H1
Related parts for MT8HTF12864AZ-800H1
MT8HTF12864AZ-800H1 Summary of contents
Page 1
... DDR2 SDRAM UDIMM MT8HTF12864AZ – 1GB Features • 240-pin, unbuffered dual in-line memory module • Fast data transfer rates: PC2-3200, PC2-4200, PC2-5300, PC2-6400, or PC2-8500 • 1GB (128 Meg x 64) • 1.8V DD DDQ • 1.7–3.6V DDSPD • JEDEC-standard 1.8V I/O (SSTL_18-compatible) • ...
Page 2
... The data sheet for the base device can be found on Micron’s Web site. Notes: 2. All part numbers end with a two-place code (not shown) that designates component and PCB revisions. Consult factory for current revision codes. Example: MT8HTF12864AZ-800H1. PDF: 09005aef83b94f21 htf8c128x64az – Rev. B 3/10 EN ...
Page 3
Pin Assignments Table 4: Pin Assignments 240-Pin UDIMM Front Pin Symbol Pin Symbol Pin DQ19 61 REF DQ0 33 DQ24 63 4 DQ1 34 DQ25 ...
Page 4
... Pin Descriptions The pin description table below is a comprehensive list of all possible pins for all DDR2 modules. All pins listed may not be supported on this module. See Pin Assignments for information specific to this module. Table 5: Pin Descriptions Symbol Type Ax Input BAx Input ...
Page 5
... SPD EEPROM power supply: 1.7–3.6V. Reference voltage: V /2. DD Ground. No connect: These pins are not connected on the module. No function: These pins are connected within the module, but provide no functionality. Not used: These pins are not used in specific module configurations/operations. Reserved for future use. 5 Pin Descriptions and V ...
Page 6
Functional Block Diagram Figure 2: Functional Block Diagram S0# DQS0 DQS0 DM0 DM CS# DQ DQS# DQ DQ0 DQ DQ1 DQ DQ2 DQ DQ3 DQ4 DQ DQ DQ5 DQ DQ6 DQ DQ7 DQS1# DQS1 DM1 DM CS# DQ ...
Page 7
... DRAM core and eight corresponding n-bit-wide, one-half-clock-cycle data trans- fers at the I/O pins. DDR2 modules use two sets of differential signals: DQS, DQS# to capture data and CK and CK# to capture commands, addresses, and control signals. Differential clocks and data strobes ensure exceptional noise immunity for these signals and provide precise crossing points to capture input signals ...
Page 8
... Electrical Specifications Stresses greater than those listed may cause permanent damage to the module. This is a stress rating only, and functional operation of the module at these or any other condi- tions outside those indicated in the device data sheet is not implied. Exposure to absolute maximum rating conditions for extended periods may adversely affect reliability. ...
Page 9
... Component specifications are available on Micron's Web site. Module speed grades cor- relate with component speed grades. Table 7: Module and Component Speed Grades DDR2 components may exceed the listed module speed grades; module may not be available in all listed speed grades Module Speed Grade -1GA ...
Page 10
I Specifications DD Table 8: DDR2 I Specifications and Conditions – 1GB DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb (128 Meg x 8) com- ponent data sheet Parameter Operating one ...
Page 11
Table 8: DDR2 I Specifications and Conditions – 1GB (Continued) DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb (128 Meg x 8) com- ponent data sheet Parameter Operating bank interleave read ...
Page 12
Serial Presence-Detect For the latest SPD data, refer to Micron's SPD page: www.micron.com/SPD. Table 9: SPD EEPROM Operating Conditions Parameter/Condition Supply voltage Input high voltage: logic 1; All inputs Input low voltage: logic 0; All inputs Output low voltage: I ...
Page 13
... FRONT VIEW 133.5 (5.256) 133.2 (5.244 0.76 (0.03) R 0.8 (0.031) TYP 123.0 (4.840) TYP BACK VIEW No Components This Side of Module 5.0 (0.197) TYP 63.0 (2.48) TYP additional design dimensions. times occur. 13 Module Dimensions U7 U8 30.5 (1.2) 29.85 (1.175) 17.78 (0.7) TYP 10 ...