DE1E3KX472MA5BA01 Murata Electronics, DE1E3KX472MA5BA01 Datasheet - Page 15

no-image

DE1E3KX472MA5BA01

Manufacturer Part Number
DE1E3KX472MA5BA01
Description
Cap Ceramic 0.0047uF 250VAC E 20% 15 X 8mm RDL 10mm Bulk
Manufacturer
Murata Electronics
Type
Radialr
Datasheet

Specifications of DE1E3KX472MA5BA01

Package/case
15(Max) X 8(Max)
Lead Pitch For Radial
10 mm
Capacitance Value
0.0047 uF
Dielectric
E
Tolerance
20 %
Voltage
250 Vac
Product Depth
8(Max) mm
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
!Note
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
No.
Item
Appearance
Capacitance
Change
Soldering
I.R.
9
Effect
(Non-Preheat)
Dielectric
Strength
Appearance
Capacitance
Change
I.R.
Soldering
10
Effect
(On-Preheat)
Dielectric
Strength
Appearance
Capacitance
Vibration
11
Resistance
D.F.
Q
Appearance
Capacitance
Change
Humidity
(Under
12
Steady
D.F.
State)
Q
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Humidity
13
Loading
D.F.
Q
I.R.
Dielectric
Strength
*
1
"C" expresses nominal capacitance value (pF).
*
2
"room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Type KY/KH/KX Specifications and Test Methods
Specifications
No marked defect
Within ±10%
1000MΩ min.
Per Item 6
No marked defect
Within ±10%
1000MΩ min.
Per Item 6
No marked defect
Within the specified tolerance
Char.
Specifications
D.F.V2.5%
B, E
D.F.V5.0%
F
QU400+20C *
1
(CF30pF)
SL
QU1000
(CU30pF)
No marked defect
Char.
Capacitance Change
B
Within ±10%
E, F
Within ±15%
SL
Within ± 5%
Char.
Specifications
D.F.V5.0%
B, E
D.F.V7.5%
F
QU275+5/2C *
1
(CF30pF)
SL
QU350
(CU30pF)
3000MΩ min.
Per Item 6
No marked defect
Char.
Capacitance Change
B
Within ±10%
E, F
Within ±15%
SL
Within ± 5%
Char.
Specifications
D.F.V5.0%
B, E
D.F.V7.5%
F
QU275+5/2C *
1
(CF30pF)
SL
QU350
(CU30pF)
3000MΩ min.
Per Item 6
Specifications and Test Methods
Test Method
As shown in figure, the lead wires
Thermal
should be immersed in solder of
Screen
350±10°C or 260±5°C up to 1.5
to 2.0mm from the root of terminal
for 3.5±0.5 sec. (10±1 sec. for
260±5°C).
Pre-treatment:
Capacitor should be stored at 85±2°C for 1 hr., then placed at
room condition*
2
for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition*
First the capacitor should be
Thermal
stored at 120+0/-5°C for
Screen
60+0/-5 sec.
Then, as in figure, the lead wires
should be immersed in solder of
260+0/-5°C up to 1.5 to 2.0mm
from the root of terminal for
7.5+0/-1 sec.
Pre-treatment:
Capacitor should be stored at 85±2°C for 1 hr., then placed at
room condition*
2
for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition*
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
total amplitude, with about a 1 minute rate of vibration change
from 10Hz to 55Hz and back to 10Hz.
Apply for a total of 6 hrs., 2 hrs. each in 3 mutually
perpendicular directions.
Set the capacitor for 500±12 hrs. at 40±2°C in 90 to 95%
relative humidity.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition*
Apply the rated voltage for 500±12 hrs. at 40±2°C in 90 to 95%
relative humidity.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition*
Continued on the following page.
C85E.pdf
08.10.29
Capacitor
1.5
to 2.0mm
Molten
Solder
2
.
4
Capacitor
1.5
to 2.0mm
Molten
Solder
2
.
2
.
2
.
13

Related parts for DE1E3KX472MA5BA01