DE1E3KX472MA5BA01

Manufacturer Part NumberDE1E3KX472MA5BA01
DescriptionCap Ceramic 0.0047uF 250VAC E 20% 15 X 8mm RDL 10mm Bulk
ManufacturerMurata Electronics
TypeRadial
DE1E3KX472MA5BA01 datasheet
 


Specifications of DE1E3KX472MA5BA01

Package/case15(Max) X 8(Max)Lead Pitch For Radial10 mm
Capacitance Value0.0047 uFDielectricE
Tolerance20 %Voltage250 Vac
Product Depth8(Max) mm  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Page 21
22
Page 22
23
Page 23
24
Page 24
25
Page 25
26
Page 26
27
Page 27
28
Page 28
29
Page 29
30
Page 30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
Page 21/72

Download datasheet (2Mb)Embed
PrevNext
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
No.
Item
Appearance
No marked defect
Capacitance
Change
Humidity
16
Loading
D.F.
I.R.
1000MΩ min.
Dielectric
Per Item 6
Strength
Appearance
No marked defect
Capacitance
Change
17
Life
I.R.
1000MΩ min.
Dielectric
Per Item 6
Strength
The capacitor flame discontinued as follows.
18
Flame Test
Tensile
Robustness
Lead wire should not be cut off. Capacitor should
19
of
not be broken.
Terminations
Bending
Appearance
No marked defect
Capacitance
Change
D.F.
Temperature
I.R.
1000MΩ min.
and
20
Immersion
Cycle
Dielectric
Per Item 6
Strength
*
1
"room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
DEJ Series Specifications and Test Methods
Specifications
Char.
Capacitance Change
E
Within ±20%
F
Within ±30%
Char.
Specifications
D.F.V5.0%
E
D.F.V7.5%
F
Char.
Capacitance Change
E
Within ±20%
F
Within ±30%
Cycle
Time (sec.)
1 to 2
15 max.
3
60 max.
Char.
Capacitance Change
E
Within ±20%
F
Within ±30%
Char.
Specifications
D.F.V5.0%
E
D.F.V7.5%
F
Test Method
Apply the rated voltage for 500±12 hrs. at 40±2˚C in 90 to 95%
relative humidity.
Pre-treatment:
Capacitor should be stored at 85±2˚C for 1 hr., then placed at
room condition*
1
for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition*
Apply a voltage of Table 2 for 1500 hrs. at 85±2˚C, relative
humidity 50% max.
<Table 2>
Applied Voltage
AC500V(r.m.s.), except that once each hour the voltage
is increased to AC1000V(r.m.s.) for 0.1 sec.
Pre-treatment:
Capacitor should be stored at 85±2˚C for 1 hr., then placed at
room condition*
1
for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 4 to 24 hrs. at room condition*
The capacitor should be subjected
to applied flame for 15 sec. and then
removed for 15 sec. until 3 cycles
are completed.
Gas Burner: Inside Dia. 9.5
As shown in figure at right, fix the body of
capacitor, apply a tensile weight gradually to
each lead wire in the radial direction of capacitor
up to 10N and keep it for 10±1 sec.
Each lead wire should be subjected to 5N weight and then a
90° bend, at the point of egress, in one direction, return to
original position, and then apply a 90° bend in the opposite
direction at the rate of one bend in 2 to 3 sec.
The capacitor should be subjected to 5 temperature cycles,
then consecutively to 2 immersion cycles.
<Temperature Cycle>
Step
Temperature (ºC)
Time (min)
1
-25+0/-3
2
Room temp.
3
85+3/-0
4
Room temp.
Cycle time: 5 cycle
<Immersion Cycle>
Time
Immersion
Step
Temperature (ºC)
(min)
1
65+5/-0
15
2
0±3
15
Cycle time: 2 cycle
Pre-treatment:
Capacitor should be stored at 85±2˚C for 1 hr., then placed at
room condition*
1
for 24±2 hrs.
Post-treatment:
Capacitor should be stored for 4 to 24 hrs. at room condition*
C85E.pdf
08.10.29
1
.
5
1
.
Capacitor
Flame
(in mm)
W
30
3
30
3
Water
Clean
water
Salt
water
1
.
19