DE1E3KX472MA5BA01

Manufacturer Part NumberDE1E3KX472MA5BA01
DescriptionCap Ceramic 0.0047uF 250VAC E 20% 15 X 8mm RDL 10mm Bulk
ManufacturerMurata Electronics
TypeRadial
DE1E3KX472MA5BA01 datasheet
 


Specifications of DE1E3KX472MA5BA01

Package/case15(Max) X 8(Max)Lead Pitch For Radial10 mm
Capacitance Value0.0047 uFDielectricE
Tolerance20 %Voltage250 Vac
Product Depth8(Max) mm  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Page 41
42
Page 42
43
Page 43
44
Page 44
45
Page 45
46
Page 46
47
Page 47
48
Page 48
49
Page 49
50
Page 50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
Page 44/72

Download datasheet (2Mb)Embed
PrevNext
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
DEA Series Specifications and Test Methods
No.
Item
1
Operating Temperature Range
2
Appearance and Dimensions
3
Marking
Between Lead
Wires
Dielectric
4
Strength
Body Insulation
Insulation
Between Lead
5
Resistance (I.R.)
Wires
6
Capacitance
7
Q
8
Temperature Characteristics
8
Pull
9
Strength of Lead
Bending
Appearance
Capacitance
Vibration
10
Resistance
Q
11 Solderability of Leads
Appearance
Capacitance
Soldering Effect
Change
12
(Non-Preheat)
Dielectric Strength
(Between Lead
Wires)
*
1
"room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
*
2
"C" expresses nominal capacitance value (pF).
42
Specifications
-25 to +125°C
No marked defect on appearance form
The capacitor should be visually inspected for evidence of
and dimensions are within specified
defect. Dimensions should be measured with slide calipers.
range.
To be easily legible
The capacitor should be visually inspected.
The capacitor should not be damaged when DC voltage of
No failure
200% of the rated voltage is applied between the lead wires for
1 to 5 sec. (Charge/Discharge currentV50mA)
The capacitor is placed in the container with
metal balls of diameter 1mm so that each
lead wire, short circuited, is kept about 2mm
off the metal balls as shown in the figure at
No failure
right, and AC1250V(r.m.s.) <50/60Hz> is
applied for 1 to 5 sec. between capacitor
lead wires and metal balls.
(Charge/Discharge currentV50mA)
The insulation resistance should be measured with
10000MΩ min.
DC500±50V within 60±5 sec. of charging.
The capacitance should be measured at 20°C with 1±0.2MHz
Within specified tolerance
and AC5V(r.m.s.) max.
min. (30pF under)
The Q should be measured at 20°C with 1±0.2MHz and
400+20C*
2
1000 min. (30pF min.)
AC5V(r.m.s.) max.
+350 to -1000ppm/°C
The capacitance measurement should be made at each step
(Temp. range: +20 to +85°C)
specified in Table.
Step
1
2
Temp. (°C)
20±2
-25±3
As shown in the figure at right, fix the body of
the capacitor and apply a tensile weight
gradually to each lead wire in the radial
direction of the capacitor up to 10N (5N for
lead diameter 0.5mm), and keep it for 10±1
Lead wire should not be cut off.
sec.
Capacitor should not be broken.
Each lead wire should be subjected to 5N (2.5N for lead
diameter 0.5mm) of weight and bent 90° at the point of egress,
in one direction, then returned to its original position and bent
90° in the opposite direction at the rate of one bend in 2 to 3
sec.
No marked defect
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
Within specified tolerance
total amplitude, with about a 1 minute rate of vibration change
400+20C*
2
min. (30pF under)
from 10Hz to 55Hz and back to 10Hz. Apply for a total of 6 hrs.,
1000 min. (30pF min.)
2 hrs. each in 3 mutually perpendicular directions.
The lead wire of a capacitor should be dipped into a ethanol
solution of 25wt% rosin and then into molten solder for 2±0.5
Lead wire should be soldered with
sec. In both cases the depth of dipping is up to about 1.5 to
uniform coating on the axial direction
2mm from the root of lead wires.
over 3/4 of the circumferential direction.
Temp. of solder: Lead Free Solder (Sn-3Ag-0.5Cu) 245±5°C
No marked defect
The lead wire should be immersed into the melted solder of
350±10°C (Body of ø5mm and under: 270±5°C) up to about 1.5
Within ±2.5%
to 2mm from the main body for 3.5±0.5 sec.
(Body of ø5mm and under: 5±0.5 sec.)
Post-treatment:
Per item 4.
Capacitor should be stored for 1 to 2 hrs. at room condition*
Test Method
About 2mm
Metal balls
3
4
5
20±2
85±2
20±2
W
H63 Eutectic Solder 235±5°C
Continued on the following page.
C85E.pdf
08.10.29
1
.