DE1E3KX472MA5BA01

Manufacturer Part NumberDE1E3KX472MA5BA01
DescriptionCap Ceramic 0.0047uF 250VAC E 20% 15 X 8mm RDL 10mm Bulk
ManufacturerMurata Electronics
TypeRadial
DE1E3KX472MA5BA01 datasheet
 


Specifications of DE1E3KX472MA5BA01

Package/case15(Max) X 8(Max)Lead Pitch For Radial10 mm
Capacitance Value0.0047 uFDielectricE
Tolerance20 %Voltage250 Vac
Product Depth8(Max) mm  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Page 41
42
Page 42
43
Page 43
44
Page 44
45
Page 45
46
Page 46
47
Page 47
48
Page 48
49
Page 49
50
Page 50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
Page 49/72

Download datasheet (2Mb)Embed
PrevNext
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
No.
Item
1
Operating Temperature Range
2
Appearance and Dimensions
3
Marking
Between Lead
Wires
Dielectric
4
Strength
Body Insulation
Insulation
Between Lead
5
Resistance (I.R.)
Wires
6
Capacitance
7
Dissipation Factor (D.F.)
8
Temperature Characteristics
Pull
9
Strength of Lead
Bending
Appearance
Capacitance
Vibration
10
Resistance
D.F.
11 Solderability of Leads
Appearance
Capacitance
Change
Soldering Effect
12
(Non-Preheat)
Dielectric Strength
(Between Lead
Wires)
* "room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
DEB Series Specifications and Test Methods
Specifications
-25 to +85°C
No marked defect on appearance form
The capacitor should be visually inspected for evidence of
and dimensions are within specified
defect. Dimensions should be measured with slide calipers.
range.
To be easily legible
The capacitor should be visually inspected.
The capacitor should not be damaged when DC voltage of
No failure
200% of the rated voltage is applied between the lead wires for
1 to 5 sec. (Charge/Discharge currentV50mA)
The capacitor is placed in the container
with metal balls of diameter 1mm so that
each lead wire, short circuited, is kept
about 2mm off the metal balls as shown in
No failure
the figure at right, and DC voltage of 1.3kV
is applied for 1 to 5 sec. between capacitor
lead wires and metal balls.
(Charge/Discharge currentV50mA)
The insulation resistance should be measured with
10000MΩ min.
DC500±50V within 60±5 sec. of charging.
The capacitance should be measured at 20°C with 1±0.2kHz
Within specified tolerance
and AC5V(r.m.s.) max.
The dissipation factor should be measured at 20°C with
Char. B, E: 2.5% max.
Char. F: 5.0% max.
1±0.2kHz and AC5V(r.m.s.) max.
Char. B: Within ±10%
The capacitance measurement should be made at each step
Char. E: Within +20/-55%
specified in Table.
Char. F: Within +30/-80%
Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr., then placed at
room condition* for 24±2 hrs. before measurements.
Step
1
2
Temp. (°C)
20±2
-25±3
As shown in the figure at right, fix the body of
the capacitor and apply a tensile weight
gradually to each lead wire in the radial
direction of the capacitor up to 10N (5N for
lead diameter 0.5mm), and keep it for 10±1
Lead wire should not be cut off.
sec.
Capacitor should not be broken.
Each lead wire should be subjected to 5N (2.5N for lead
diameter 0.5mm) of weight and bent 90° at the point of egress,
in one direction, then returned to its original position and bent
90° in the opposite direction at the rate of one bend in 2 to 3
sec.
No marked defect
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
Within specified tolerance
total amplitude, with about a 1 minute rate of vibration change
Char. B, E: 2.5% max.
from 10Hz to 55Hz and back to 10Hz. Apply for a total of 6 hrs.,
Char. F: 5.0% max.
2 hrs. each in 3 mutually perpendicular directions.
The lead wire of a capacitor should be dipped into a ethanol
solution of 25wt% rosin and then into molten solder for 2±0.5
Lead wire should be soldered with
sec. In both cases the depth of dipping is up to about 1.5 to
uniform coating on the axial direction
2mm from the root of lead wires.
over 3/4 of the circumferential direction.
Temp. of solder: Lead Free Solder (Sn-3Ag-0.5Cu) 245±5°C
No marked defect
The lead wire should be immersed into the melted solder of
350±10°C (Body of ø5mm and under: 270±5°C) up to about 1.5
Char. B: Within ±5%
to 2mm from the main body for 3.5±0.5 sec.
Char. E: Within ±15%
(Body of ø5mm and under: 5±0.5 sec.)
Char. F: Within ±20%
Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,
Per item 4.
Post-treatment: Capacitor should be stored for 4 to 24 hrs. at
Test Method
About 2mm
Metal balls
3
4
5
20±2
85±2
20±2
W
H63 Eutectic Solder 235±5°C
then placed at room condition* for 24±2 hrs.
before initial measurements.
room condition*.
Continued on the following page.
C85E.pdf
08.10.29
9
47