DE1E3KX472MA5BA01

Manufacturer Part NumberDE1E3KX472MA5BA01
DescriptionCap Ceramic 0.0047uF 250VAC E 20% 15 X 8mm RDL 10mm Bulk
ManufacturerMurata Electronics
TypeRadial
DE1E3KX472MA5BA01 datasheet
 


Specifications of DE1E3KX472MA5BA01

Package/case15(Max) X 8(Max)Lead Pitch For Radial10 mm
Capacitance Value0.0047 uFDielectricE
Tolerance20 %Voltage250 Vac
Product Depth8(Max) mm  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Page 51
52
Page 52
53
Page 53
54
Page 54
55
Page 55
56
Page 56
57
Page 57
58
Page 58
59
Page 59
60
Page 60
61
62
63
64
65
66
67
68
69
70
71
72
Page 57/72

Download datasheet (2Mb)Embed
PrevNext
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
No.
Item
1
Operating Temperature Range
2
Appearance and Dimensions
3
Marking
Between Lead
Wires
Dielectric
4
Strength
Body Insulation
Insulation
Between Lead
5
Resistance (I.R.)
Wires
6
Capacitance
7
Q
8
Temperature Characteristics
Pull
9
Strength of Lead
Bending
Appearance
Vibration
Capacitance
10
Resistance
Q
11 Solderability of Leads
Appearance
Capacitance
Soldering Effect
Change
12
(Non-Preheat)
Dielectric Strength
(Between Lead
Wires)
*
1
"room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
*
2
"C" expresses nominal capacitance value (pF).
DEF Series Specifications and Test Methods
Specifications
-25 to +105°C
No marked defect on appearance form
The capacitor should be visually inspected for evidence of
and dimensions are within specified
defect. Dimensions should be measured with slide calipers.
range.
To be easily legible
The capacitor should be visually inspected.
The capacitor should not be damaged when DC12.6kV is
No failure
applied between the lead wires for 1 to 5 sec.
(Charge/Discharge currentV50mA)
The capacitor is placed in the container
with metal balls of diameter 1mm so that
each lead wire, short circuited, is kept
about 2.0mm off the metal balls as shown
No failure
in the figure at right, and DC voltage of
1.3kV is applied for 1 to 5 sec. between
capacitor lead wires and metal balls.
(Charge/Discharge currentV50mA)
The insulation resistance should be measured with
10000MΩ min.
DC500±50V within 60±5 sec. of charging.
The capacitance should be measured at 20°C with 1±0.2MHz
Within specified tolerance
and AC5V(r.m.s.) max.
min. (30pF under)
The Q should be measured at 20°C with 1±0.2MHz and
400+20C*
2
1000 min. (30pF min.)
AC5V(r.m.s.) max.
Char. CH: 0±60ppm/°C
The capacitance measurement should be made at each step
Char. SL: +350 to -1000ppm/°C
specified in Table.
(Temp. range: +20 to +85°C)
1
2
Step
Temp. (°C)
20±2
-25±3
As shown in the figure at right, fix the body of
the capacitor and apply a tensile weight
gradually to each lead wire in the radial
direction of the capacitor up to 10N and keep
Lead wire should not be cut off.
it for 10±1 sec.
Capacitor should not be broken.
Each lead wire should be subjected to 5N of weight and bent
90° at the point of egress, in one direction, then returned to its
original position and bent 90° in the opposite direction at the
rate of one bend in 2 to 3 sec.
No marked defect
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
Within specified tolerance
total amplitude, with about a 1 minute rate of vibration change
400+20C*
2
min. (30pF under)
from 10Hz to 55Hz and back to 10Hz. Apply for a total of 6 hrs.,
1000 min. (30pF min.)
2 hrs. each in 3 mutually perpendicular directions.
The lead wire of a capacitor should be dipped into a ethanol
solution of 25wt% rosin and then into molten solder for 2±0.5
Lead wire should be soldered with
sec. In both cases the depth of dipping is up to about 1.5 to
uniform coating on the axial direction
2.0mm from the root of lead wires.
over 3/4 of the circumferential direction.
Temp. of solder: Lead Free Solder (Sn-3Ag-0.5Cu) 245±5°C
No marked defect
The lead wire should be immersed into the melted solder of
Within ±2.5%
350±10°C up to about 1.5 to 2.0mm from the main body for
3.5±0.5 sec.
Post-treatment: Capacitor should be stored for 1 to 2 hrs. at
Per item 4.
Test Method
About
2.0mm
Metal balls
3
4
5
20±2
85±2
20±2
W
H63 Eutectic Solder 235±5°C
room condition*
1
.
Continued on the following page.
C85E.pdf
08.10.29
11
55