EPM3064ATC44-10 Altera, EPM3064ATC44-10 Datasheet - Page 38

• Manufacturer Part Number: EPM3064ATC44-10
• Description: IC MAX 3000A CPLD 64 44-TQFP
• Manufacturer: Altera
• Series: MAX® 3000Ar

Specifications of EPM3064ATC44-10

• Programmable Type: In System Programmable
• Delay Time Tpd(1) Max: 10.0ns
• Voltage Supply - Internal: 3 V ~ 3.6 V
• Number Of Logic Elements/blocks: 4
• Number Of Macrocells: 64
• Number Of Gates: 1250
• Number Of I /o: 34
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 44-TQFP, 44-VQFP
• Voltage: 3.0 V ~ 3.6 V
• Memory Type: EEPROM
• Number Of Logic Elements/cells: 4
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Other names: 544-1159

MAX 3000A Programmable Logic Device Family Data Sheet
Notes to tables:
(1)
(2)
(3)
(4)
(5)
38
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
OD3
ZX1
ZX2
ZX3
XZ
SU
H
FSU
FH
RD
COMB
IC
EN
GLOB
PRE
CLR
PIA
LPA
Table 25. EPM3512A Internal Timing Parameters (Part 2 of 2)
Symbol
These values are specified under the recommended operating conditions, as shown in
Figure 11 on page 27
These values are specified for a PIA fan–out of one LAB (16 macrocells). For each additional LAB fan–out in these
devices, add an additional 0.1 ns to the PIA timing value.
This minimum pulse width for preset and clear applies for both global clear and array controls. The t
must be added to this minimum width if the clear or reset signal incorporates the t
path.
These parameters are measured with a 16–bit loadable, enabled, up/down counter programmed into each LAB.
The t
running in low–power mode.
LPA
Output buffer and pad delay,
slow slew rate = on
V
Output buffer enable delay,
slow slew rate = off
V
Output buffer enable delay,
slow slew rate = off
V
Output buffer enable delay,
slow slew rate = on
V
Output buffer disable delay
Register setup time
Register hold time
Register setup time of fast input
Register hold time of fast input
Register delay
Combinatorial delay
Array clock delay
Register enable time
Global control delay
Register preset time
Register clear time
PIA delay
Low-power adder
parameter must be added to the t
CCIO
CCIO
CCIO
CCIO
= 2.5 V or 3.3 V
= 3.3 V
= 2.5 V
= 3.3 V
Parameter
for more information on switching waveforms.
LAD
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 5 pF
(2)
(5)
Conditions
, t
LAC
, t
IC
, t
EN
, t
SEXP
Min
2.1
0.6
1.6
1.4
, t
ACL
-7
Note (1)
, and t
Max
Speed Grade
6.0
4.0
4.5
9.0
4.0
1.3
0.6
1.8
1.0
1.7
1.0
1.0
3.0
4.5
CPPW
LAD
parameters for macrocells
Min
3.0
0.8
1.6
1.4
Table 13 on page
parameter into the signal
-10
Altera Corporation
Max
10.0
6.5
5.0
5.5
5.0
1.7
0.8
2.3
1.3
2.2
1.4
1.4
4.0
5.0
LPA
parameter
23. See
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns