IC MAX 3000A CPLD 64 100-TQFP

EPM3064ATC100-10N

Manufacturer Part NumberEPM3064ATC100-10N
DescriptionIC MAX 3000A CPLD 64 100-TQFP
ManufacturerAltera
SeriesMAX® 3000A
EPM3064ATC100-10N datasheet
 


Specifications of EPM3064ATC100-10N

Programmable TypeIn System ProgrammableDelay Time Tpd(1) Max10.0ns
Voltage Supply - Internal3 V ~ 3.6 VNumber Of Logic Elements/blocks4
Number Of Macrocells64Number Of Gates1250
Number Of I /o66Operating Temperature0°C ~ 85°C
Mounting TypeSurface MountPackage / Case100-TQFP, 100-VQFP
Voltage3.0 V ~ 3.6 VMemory TypeEEPROM
Number Of Logic Elements/cells4Lead Free Status / RoHS StatusLead free / RoHS Compliant
Features-Other names544-1974
EPM3064ATC100-10N
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Page 21
22
Page 22
23
Page 23
24
Page 24
25
Page 25
26
Page 26
27
Page 27
28
Page 28
29
Page 29
30
Page 30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Page 24/46

Download datasheet (710Kb)Embed
PrevNext
MAX 3000A Programmable Logic Device Family Data Sheet
Table 15. MAX 3000A Device Capacitance
Symbol
Parameter
C
Input pin capacitance
IN
C
I/O pin capacitance
I/O
Notes to tables:
(1)
See the
Operating Requirements for Altera Devices Data
(2)
Minimum DC input voltage is –0.5 V. During transitions, the inputs may undershoot to –2.0 V or overshoot to
5.75 V for input currents less than 100 mA and periods shorter than 20 ns.
(3)
All pins, including dedicated inputs, I/O pins, and JTAG pins, may be driven before V
powered.
(4)
These values are specified under the recommended operating conditions, as shown in
(5)
The parameter is measured with 50% of the outputs each sourcing the specified current. The I
to high–level TTL or CMOS output current.
(6)
The parameter is measured with 50% of the outputs each sinking the specified current. The I
low–level TTL, PCI, or CMOS output current.
(7)
This value is specified during normal device operation. During power-up, the maximum leakage current is
μ
±300
A.
(8)
This pull–up exists while devices are programmed in–system and in unprogrammed devices during power–up.
(9)
Capacitance is measured at 25° C and is sample–tested only. The
has a maximum capacitance of 20 pF.
(10) The POR time for all MAX 3000A devices does not exceed 100 μs. The sufficient V
3.0 V. The device is fully initialized within the POR time after V
(11) These devices support in-system programming for
and 0° C, contact Altera Applications.
Figure 9
devices.
24
Note (9)
Conditions
V
= 0 V, f = 1.0 MHz
IN
V
= 0 V, f = 1.0 MHz
OUT
Sheet.
pin (high–voltage pin during programming)
OE1
reaches the sufficient POR voltage level.
CCINT
–40° to 100° C. For in-system programming support between –40°
shows the typical output drive characteristics of MAX 3000A
Min
Max
Unit
8
pF
8
pF
and V
are
CCINT
CCIO
Table 13 on page
23.
parameter refers
OH
parameter refers to
OL
voltage level for POR is
CCINT
Altera Corporation