RC20GF151JTR IRC, RC20GF151JTR Datasheet

Carbon Composition Resistors 150 OHM 5%TR

RC20GF151JTR

Manufacturer Part Number
RC20GF151JTR
Description
Carbon Composition Resistors 150 OHM 5%TR
Manufacturer
IRC
Series
RC20r
Datasheet

Specifications of RC20GF151JTR

Resistance
150 Ohms
Tolerance
5 %
Power Rating
0.5 Watt (1/2 Watt)
Voltage Rating
350 Volts
Temperature Coefficient
+/- 150 PPM / C
Operating Temperature Range
- 55 C to + 130 C
Dimensions
3.6 mm Dia. x 9.5 mm L
Product
Resistors Carbon Composition
Termination Style
Axial
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Electrical Data
General Note
IRC reserves the right to make changes in product specifi cation without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Wire and Film Technologies Division
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
SP20 / SP20F Series
General Purpose Failsafe
Molded Wirewound Resistor
IRC Type
EIA RS-344 Style
MIL-R-11 Style
Resistance - Std.
Tolerance - Std.
Power Rating
Max. Continuous Working Voltage
Min. Insulation
Resistance
Min. Dielectric
Withstanding Volts
(RMS)
Hotspot Temperature Rise
Typical Load Life
Current Noise
SP20F Fusible
±5%, ±10% tolerance
0.1 ohm to 1200 ohms
F version has fl ame resistant coating
1 watt rated with 1/2 watt dimensions
Drop-in replacement BW20 / BW20F
Weldable and solderable magnetic lead
TCR’s as low as ±150 ppm/°C standard (custom TC’s available)
Lead free, RoHS compliant construction available
Reduced Pressure
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
ATM
Wet
Dry
Derating to 0 @ 160°C
1/2 watt @ 100°C
120°C @ 1 watts
3/4 watt @ 70°C
0.1Ω to 1200Ω
1 watt @ 50°C
RC20/RC32
10,000 Meg
±5%, ±10%
Negligible
100 Meg
CRU1
SP20
700V
450V
5%
PR
Derating to 0 @ 160°C
120°C @ 1 watts
3/4 watt @ 70°C
0.1Ω to 1000Ω
1 watt @ 50°C
RC20/RC32
10,000 Meg
±5%, ±10%
Negligible
100 Meg
SP20F
CRU1
700V
450V
5%
---
PR
2
1. Resistive Element
All resistor types have resistance alloy
winding on a braided fi berglass substrate.
Intermediate silicone coatings are used
to enhance processibility and to provide
protection to the resistive element.
2. Termination
The SP-20 and SP-20F resistors are
terminated using an alloy coated copper
fl ashed steel lead welded to a cap of the
same material. This termination assembly is
mechanically crimped, utilizing an improved
crimp design, to the resistive element.
3. Encapsulation
The SP-20 and the SP20F are encapsulated
utilizing a compression molded phenolic
plastic material. The SP-20F has a fl ame
resistance coating applied over the resistive
element to provide fl ammability protection
when destructive overloads may occur.
4. Marking
All products are marked utilizing heat and
solvent resistant color code bands consistent
with EIA/MIL requirements. The fi rst band
is double width to designate wirewound
construction. A fi fth band, blue in color, is
used for fl ameproof identifi cation.
1
(See notes below)
SP20/SP20F Series Issue September 2010 Sheet 1 of 3
3
4
TT electronics plc
A subsidiary of

Related parts for RC20GF151JTR

RC20GF151JTR Summary of contents

Page 1

... General Note IRC reserves the right to make changes in product specifi cation without notice or liability. All information is subject to IRC’s own data and is considered accurate at time of going to print. Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • ...

Page 2

... SP20F (9.91 ± 0.25) Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com SP20 <1R <±800 ≥1R <±150 700V ...

Page 3

... Custom design identifi er for non-standard products Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com SP-20F Power Derating Curve 2.5 2.0 1 ...

Related keywords