IC FLEX 10K FPGA 30K 208-RQFP

EPF10K30RI208-4

Manufacturer Part NumberEPF10K30RI208-4
DescriptionIC FLEX 10K FPGA 30K 208-RQFP
ManufacturerAltera
SeriesFLEX-10K®
EPF10K30RI208-4 datasheet
 


Specifications of EPF10K30RI208-4

Number Of Logic Elements/cells1728Number Of Labs/clbs216
Total Ram Bits12288Number Of I /o147
Number Of Gates69000Voltage - Supply4.5 V ~ 5.5 V
Mounting TypeSurface MountOperating Temperature-40°C ~ 100°C
Package / Case208-RQFPLead Free Status / RoHS StatusContains lead / RoHS non-compliant
Other names544-2233  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Page 31
32
Page 32
33
Page 33
34
Page 34
35
Page 35
36
Page 36
37
Page 37
38
Page 38
39
Page 39
40
Page 40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
Page 39/128

Download datasheet (2Mb)Embed
PrevNext
FLEX 10K Embedded Programmable Logic Device Family Data Sheet
Slew-Rate Control
The output buffer in each IOE has an adjustable output slew rate that can
be configured for low-noise or high-speed performance. A slower slew
rate reduces system noise and adds a maximum delay of approximately
2.9 ns. The fast slew rate should be used for speed-critical outputs in
systems that are adequately protected against noise. Designers can specify
the slew rate on a pin-by-pin basis during design entry or assign a default
slew rate to all pins on a device-wide basis. The slow slew rate setting
affects only the falling edge of the output.
Open-Drain Output Option
FLEX 10K devices provide an optional open-drain (electrically equivalent
to an open-collector) output for each I/O pin. This open-drain output
enables the device to provide system-level control signals (e.g., interrupt
and write enable signals) that can be asserted by any of several devices. It
can also provide an additional wired-OR plane. Additionally, the Altera
software can convert tri-state buffers with grounded data inputs to open-
drain pins automatically.
Open-drain output pins on FLEX 10K devices (with a pull-up resistor to
the 5.0-V supply) can drive 5.0-V CMOS input pins that require a V
of
IH
3.5 V. When the open-drain pin is active, it will drive low. When the pin is
inactive, the trace will be pulled up to 5.0 V by the resistor. The open-drain
pin will only drive low or tri-state; it will never drive high. The rise time
is dependent on the value of the pull-up resistor and load impedance. The
I
current specification should be considered when selecting a pull-up
OL
resistor.
Output pins on 5.0-V FLEX 10K devices with V
= 3.3 V or 5.0 V (with
CCIO
a pull-up resistor to the 5.0-V supply) can also drive 5.0-V CMOS input
pins. In this case, the pull-up transistor will turn off when the pin voltage
exceeds 3.3 V. Therefore, the pin does not have to be open-drain.
MultiVolt I/O Interface
The FLEX 10K device architecture supports the MultiVolt I/O interface
feature, which allows FLEX 10K devices to interface with systems of
differing supply voltages. These devices have one set of V
pins for
CC
internal operation and input buffers (VCCINT) and another set for I/O
output drivers (VCCIO).
Altera Corporation
39