EE80C188EB25 Intel, EE80C188EB25 Datasheet - Page 10

• Manufacturer Part Number: EE80C188EB25
• Description: IC MPU 16-BIT 5V 25MHZ 84-PLCC
• Manufacturer: Intel

Specifications of EE80C188EB25

• Processor Type: 80C188
• Features: EB suffix, 16-Bit, Extended Temp
• Speed: 25MHz
• Voltage: 5V
• Mounting Type: Surface Mount
• Package / Case: 84-PLCC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 864077

80C186EB 80C188EB 80L186EB 80L188EB
NOTE
Pin names in parentheses apply to the 80C188EB 80L188EB
10
V
V
CLKIN
OSCOUT
CLKOUT
RESIN
RESOUT
PDTMR
NMI
TEST BUSY
(TEST)
AD15 0
(AD7 0)
CC
SS
Name
Pin
Type
Pin
I O
I O
G
O
O
O
P
I
I
I
I
Input
Type
A(E)
A(E)
A(E)
A(L)
A(L)
S(L)
Output
States
H(WH)
H(Q)
R(Q)
H(Q)
R(Q)
P(Q)
P(Q)
R(Z)
H(Z)
R(Z)
H(0)
R(1)
P(X)
P(0)
P(1)
Table 3 Pin Descriptions
POWER connections consist of four pins which must be
shorted externally to a V
GROUND connections consist of six pins which must be
shorted externally to a V
CLocK INput is an input for an external clock An external
oscillator operating at two times the required processor
operating frequency can be connected to CLKIN For crystal
operation CLKIN (along with OSCOUT) are the crystal
connections to an internal Pierce oscillator
OSCillator OUTput is only used when using a crystal to
generate the external clock OSCOUT (along with CLKIN)
are the crystal connections to an internal Pierce oscillator
This pin is not to be used as 2X clock output for non-crystal
applications (i e this pin is N C for non-crystal applications)
OSCOUT does not float in ONCE mode
CLocK OUTput provides a timing reference for inputs and
outputs of the processor and is one-half the input clock
(CLKIN) frequency CLKOUT has a 50% duty cycle and
transistions every falling edge of CLKIN
RESet IN causes the processor to immediately terminate
any bus cycle in progress and assume an initialized state All
pins will be driven to a known state and RESOUT will also
be driven active The rising edge (low-to-high) transition
synchronizes CLKOUT with CLKIN before the processor
begins fetching opcodes at memory location 0FFFF0H
RESet OUTput that indicates the processor is currently in
the reset state RESOUT will remain active as long as RESIN
remains active
Power-Down TiMeR pin (normally connected to an external
capacitor) that determines the amount of time the processor
waits after an exit from power down before resuming normal
operation The duration of time required will depend on the
startup characteristics of the crystal oscillator
Non-Maskable Interrupt input causes a TYPE-2 interrupt to
be serviced by the CPU NMI is latched internally
TEST is used during the execution of the WAIT instruction to
suspend CPU operation until the pin is sampled active
(LOW) TEST is alternately known as BUSY when interfacing
with an 80C187 numerics coprocessor (80C186EB only)
These pins provide a multiplexed Address and Data bus
During the address phase of the bus cycle address bits 0
through 15 (0 through 7 on the 80C188EB) are presented on
the bus and can be latched using ALE 8- or 16-bit data
information is transferred during the data phase of the bus
cycle
Description
CC
SS
board plane
board plane