E2E2-X10Y2 Omron, E2E2-X10Y2 Datasheet
E2E2-X10Y2
Specifications of E2E2-X10Y2
Related parts for E2E2-X10Y2
E2E2-X10Y2 Summary of contents
Page 1
... E2E2 X18MY1 E2E2 2-WIRE AC NC E2E2-X2Y2-US E2E2 X2Y2 US E2E2-X5Y2-US E2E2 X5Y2 US E2E2 X10Y2 US E2E2-X10Y2-US E2E2 X5MY2 US E2E2-X5MY2-US E2E2 X10MY2 US E2E2-X10MY2-US E2E2-X18MY2-US E2E2 X18MY2 US NC E2E2-X2Y2-M4 E2E2 X2Y2 M4 E2E2-X5Y2-M4 E2E2 X5Y2 M4 E2E2-X10Y2-M4 E2E2 X10Y2 M4 E2E2 X5MY2 M4 E2E2-X5MY2-M4 E2E2 X10MY2 M4 E2E2-X10MY2-M4 E2E2-X18MY2-M4 E2E2 X18MY2 M4 ...
Page 2
... E2E2 2-WIRE AC Part number Y92E-B12 Y92E-B18 Y92E-B30 Y92E-E12-2 Y92E-E18-2 Y92E-E30-2 Part number M12-MHWS M18-MHWS M30-MHWS E2E2-X10j-US E2E2-X18MYj-US M30 Shielded Unshielded ...
Page 3
... Sensing face PBT Note: 1. When using an M18 or M30 size E2E2 at an ambient temperature between 70°C and 85°C (158°F to 185°F), make sure the E2E2 has a control output of 200 mA maximum. 2. When supplying 24 VAC to any of the above models, make sure that the operating ambient temperature range is - -25°C to 85°C (- -13° ...
Page 4
... Load current (mA) Sensing distance X (mm) E2Ej-X18Mj E2Ej-X10Mj Y (mm) Residual output voltage Proximity Sensor 100 VAC Residual load volt- age Load current (mA) 5 E2E2 2-WIRE AC Residual output voltage Proximity Sensor 200 VAC Residual load volt- age Load current (mA) ...
Page 5
... E2E2 2-WIRE AC J SENSING DISTANCE VS. SENSING OBJECT (TYPICAL) E2E2-X2Yj Mild steel Stainless steel (SUS304) Brass Aluminum Side length of sensing object d (mm) E2E2-X5MYj Mild steel Stainless steel (SUS304) Brass Aluminum Side length of sensing object d (mm) Dimensions Unit: mm (inch) J PRE-WIRED SENSORS E2E2-X2jj 60 (2.36) 21 dia ...
Page 6
... E2E2 2-WIRE AC E2E2-X5jj 65 (2.56) 29 dia. 60 (2.36) (1.14) M18 × 1 Two clamping nut Toothed washer E2E2-X10jj 70 (2.76) 42 dia. (1.65) 65 (2.56) M30 × 1.5 Two clamping nut Toothed washer E2E2-X18Mjj 70 (2.76) 42 dia. 65 (2.56) (1.65) 13 (0.51) 26.8 dia. M30 × 1.5 Toothed washer J SENSORS WITH CONNECTORS E2E2-X2Yj- ...
Page 7
... E2E2 2-WIRE AC E2E2-X5Yj-M4 29 dia. 60 (2.36) (1.14 M18 x 1 Two clamping nut Toothed washer E2E2-X10Yj-M4 42 dia. (1.65 M30 x 1.5 Toothed washer J MOUNTING HOLES F Dimensions M12 F (mm) 12.5 mm (0.49 in) dia. Installation J PIN ARRANGEMENT E2E2-XjYj-M4 Applicable models Pin arrangement E2E2-XjYj- E2E2-X10MYj-M4 75 (2.95) 29 dia. (1.14) ...
Page 8
... (710 kgf S cm) M30 180 (1,800 kgf S cm) J EFFECTS OF SURROUNDING METAL When mounting the E2E2 within a metal panel, ensure that the clearances given in the table below are maintained. Failure to maintain these distances may cause deterioration in the perfor- mance of the sensor. Type ...
Page 9
... W minimum If these resistors generate excessive heat, use a resistor with a resistance of 10 kΩ maximum and an allowable power minimum at 100 VAC and a resistor with a resistance of 20 kΩ maximum and an allowable power minimum at 200 VAC instead. 10 E2E2 2-WIRE AC VAC power supply V S ...
Page 10
... One East Commerce Drive Schaumburg, IL 60173 1-800-55-OMRON Cat. No. CEDSAX4 11/01 OMRON ON- -LINE Global -- http://www.omron.com USA -- http://www.omron.com/oei Canada -- http://www.omron.com/oci Specifications subject to change without notice. E2E2 2-WIRE AC OMRON CANADA, INC. 885 Milner Avenue Scarborough, Ontario M1B 5V8 416-286-6465 Printed in U.S.A. ...