447-XYP1BF138-RC Xicon, 447-XYP1BF138-RC Datasheet - Page 4

no-image

447-XYP1BF138-RC

Manufacturer Part Number
447-XYP1BF138-RC
Description
Thermal Cutoffs TCO 138C 1A/250VAC
Manufacturer
Xicon
Datasheet

Specifications of 447-XYP1BF138-RC

Current Rating
1 A
Rated Temperature
138 C
Voltage Rating
250 VAC
Thermal Cutoffs (TCO)/Thermal-Links
8. Soldering, Welding, Encapsulation
9. The use of sufficiently flexible, appropriate free length and proper size wire should be used for splice connection. Connection including connectors
10. Where the lead wires of the TCO is tied with string, put them a least 10mm apart from the seals of the main body of the TCO.
11. Quality control notes:
12. Storage Method
13. Do not repair a TCO. Replace it with a new part.
Note: This specification sheet shows the quality and performance of a unit component. For quality assurance, contact us with your requirements.
1) Lead wires are to be soldered with the standard conditions shown in Table 1. Excessive soldering heat and soldering time may cause damage
2) Avoid preheating and gradual cooling as far as possible. However, if preheating and gradual cooling is done, set the process conditions after
3) Do not use reflow soldering.
4) Thin type (MT, MS Series) is not to be soldered.
5) If water or solvent is used for cleaning flux after soldering, check and confirm the reliability of the agent.
6) Lead wires are to be clamped at least 3mm away from the seals. Improper connections may cause damage to the seals or other parts and may
7) Set the conditions for welding and encapsulation only after checking contact resistance and connection strength.
8) When resoldering or rewelding, cool the TCo under room conditions.
9) When the TCO is heated by soldering or welding, be careful not to pull, push, or twist the TCO lead wires.
used for splicing shall be of the low resistance type, and they shall be made mechanically secure.
1) Measurement of resistance between lead wires (terminals) and checking of the internal status with X-rays are effective means to confirm the
2) It is not necessary to confirm normal operation of the TCO with trial units and with a prototype equipment lot set at normal and abnormal
1) Store the TCO in packing cases or in polyethylene bags within the temperature range -10°C to +40°C and RH of 30% to 75%. Store them at
2) Avoid storage in places containing corrosive gases such as sea breeze, CI
3) The period of guarantee for performance such as solderability is for 1 year after our delivery; and this condition applies only in the case
Before using, be sure to evaluate and verify the product after mounting it in your product.
Length ( )
to a TCO. If higher temperature, longer time or shorter lead length exist rather than the conditions of Table 1, it is recommended to run tests for
finding the soldering conditions that do not damage the TCO. Also, use of tools such as pliers are recommended to dissipate the soldering heat
by grasping lead wires between the TCO body and soldering point.
confirming that the TCO is not affected by these procedures.
result in nuisance tripping of the devices due to the generation of excessive heat at a faulty high resistance junction.
status of the TCO on delivery and after mounting in the equipment.
conditions.
a location where no rapid changes of temperature or humidity or no direct sunlight is applied. The location must also be free from vibration
and shock.
where the storage method specified in above has been followed.
25mm
20mm
15mm
10mm
Lead
N082, N088
N098, N109
N124, N126
N135, N143
N163, N183
N110
Temperature of Soldering: 300°C
XICON PASSIVE COMPONENTS • (800) 628-0544
F133, F139
F115, F130
F102
F168
Type No.
Time: 3s
E130, E133
E102, E115
E139
2
, H, S
2
, NH
3
, SO
H102, H115
H130, H133
2
H139
H168
and NO
447-XYP 1BF145-RC
2
.
Soldering Point
4

Related parts for 447-XYP1BF138-RC