CP2000AC54PEZ Lineage Power, CP2000AC54PEZ Datasheet - Page 7

no-image

CP2000AC54PEZ

Manufacturer Part Number
CP2000AC54PEZ
Description
Linear & Switching Power Supplies 100-120/200-240Vac +/-54Vdc 2000W
Manufacturer
Lineage Power
Datasheet

Specifications of CP2000AC54PEZ

Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Data Sheet
Signal Definitions
All hardware alarm signals (Fault, PFW, OTW, Power Capacity) are open drain FETs. These signals
should be pulled HI to either 3.3V or 5V. Maximum sink current 5mA. An active LO signal (< 0.4Vdc). All
signals are referenced to Logic GRD unless otherwise stated. Contact your Lineage Power representative
for more details.
Lineage Power
Function
Output Enable
Power Fail Warning
I
Rectifier Fault
Module Present
ON/OFF
Protocol select
Margining
Over-Temperature Warning
Power Capacity
Rectifier address
Shelf Address
Back bias
Mux Reset
Standby power
Current Share
I
I
RS485 Line
2
2
2
C Interrupt
C Line 0
C Line 1
Enable
PFW
Alert#_0
Alert#_1
Fault
MOD_PRES
ON/OFF
Protocol
Margin
OTW
POWER_CAP
Unit_addr
Shelf_addr
8V_INT
Reset
5VA
Ishare
SCL_0, SDA_0 Input
SCL_1, SDA_1 Input
RS_485+
RS_485-
Label
Input
Input
Output
Input
Input
Output
Output
Output
Output
Input
Output
Input
_
Input
Output
-
Input
Type
If shorted to LOGIC_GRD, the rectifier output is enabled
when using I
reset a latched OFF rectifier. Function not available in
RS485 mode.
An open drain FET; normally HI, indicating output power is
present. Changes to LO at least 5msec before the output
voltage is lost.
Interrupt signal via I
requested from the host controller. This signal pin is pulled
up to 3.3V via a 10kΩ resistor and switches to active LO
when an interrupt occurs.
Indicates that an internal fault exists. An open drain FET;
normally HI, changes to LO.
Short pin, see Status and Control description for further
information on this signal.
Short pin, connects last and breaks first; used to activate
and deactivate output during hot-insertion and extraction,
respectively. Ref: 54_OUT (-DC)
See Status and Control description for further information
on this signal. Ref: 54_OUT (-DC).
Allows changing of output voltage through an analog
voltage input or via resistor divider.
An open drain FET; normally HI, changes to LO
approximately 5°C prior to thermal shutdown.
An open drain FET; Used to indicate rectifier operation
mode; HI indicates 2000W operation and LO indicates
1200W operation.
Voltage level addressing of rectifiers within a single shelf.
Ref: 54_OUT (-DC).
Voltage level addressing of rectifiers within multiple
shelves. Ref: 54_OUT (-DC).
Diode OR’ed 8Vdc drain; used to back bias
microprocessors and DSP of failed rectifier from operating
rectifiers. Ref: 54_OUT (-DC).
Resets the I
5V at 0.75A provided for external use by either adjacent
power supplies or the using system.
A single wire interface between each of the power unit
forces them to share the load current. Ref: 54_OUT (-DC).
I
I
RS485 line.
2
2
C line 0.
C line 1.
2
2
CP2000AC54 Front-End Power Supply
C lines to I
C mode of operation. May also be toggled to
2
C lines indicating that service is
Description
2
C line 0.
Compact Power Line
7

Related parts for CP2000AC54PEZ