IC PD/OPTO FLYBACK CTRLR 32-DFN

LTC4269CDKD-1#PBF

Manufacturer Part NumberLTC4269CDKD-1#PBF
DescriptionIC PD/OPTO FLYBACK CTRLR 32-DFN
ManufacturerLinear Technology
TypePower Over Ethernet (PoE)
LTC4269CDKD-1#PBF datasheet
 


Specifications of LTC4269CDKD-1#PBF

ApplicationsPower Interface Switch for Power Over Ethernet (PoE) DevicesVoltage - Supply14 V ~ 16 V
Operating Temperature0°C ~ 70°CMounting TypeSurface Mount
Package / Case32-DFNCurrent - Supply1.35mA
InterfaceIEEE 802.3afController TypePowered Device Interface Controller (PD)
Input Voltage60VSupply Current6.4mA
Digital Ic Case StyleDFNNo. Of Pins32
Duty Cycle (%)88%Frequency100kHz
Operating Temperature Range0°C To +70°CMslMSL 1 - Unlimited
Rohs CompliantYesOperating Temperature (max)70C
Operating Temperature (min)0CPin Count32
MountingSurface MountPackage TypeDFN EP
Case Length7mmScreening LevelCommercial
Lead Free Status / RoHS StatusLead free / RoHS Compliant  
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Page 13/44

Download datasheet (387Kb)Embed
PrevNext
APPLICATIONS INFORMATION
Table 1. LTC4269-1 Modes of Operation as a Function
of Input Voltage
V
–V
(V)
LTC4269-1 MODES OF OPERATION
PORTP
PORTN
0V to 1.4V
Inactive (Reset After 1st Classifi cation Event)
1.5V to 9.8V
25k Signature Resistor Detection Before 1st
(5.4V to 9.8V)
Classifi cation Event (Mark, 11k Signature
Corrupt After 1st Classifi cation Event)
12.5V to ON/OFF*
Classifi cation Load Current Active
ON/OFF* to 60V
Inrush and Power Applied To PD Load
>71V
Overvoltage Lockout,
Classifi cation and Hot Swap Are Disabled
*ON/OFF includes hysteresis. Rising input threshold, 37.2V Max.
Falling input threshold, 30V Min.
These modes satisfy the requirements defi ned in the
IEEE 802.3af/IEEE 802.3at specifi cation.
INPUT DIODE BRIDGE
In the IEEE 802.3af/IEEE 802.3at standard, the modes of
operation reference the input voltage at the PD’s RJ45
connector. Since the PD must handle power received in
either polarity from either the data or the spare pair, input
diode bridges BR1 and BR2 are connected between the
RJ45 connector and the LTC4269-1 (Figure 2).
POWERED
DEVICE
(PD)
INPUT
Figure 2. PD Front End Using Diode Bridges on Main and Spare Inputs
The input diode bridge introduces a voltage drop that
affects the range for each mode of operation. The
LTC4269-1 compensates for these voltage drops so that a
PD built with the LTC4269-1 meets the IEEE 802.3af/IEEE
802.3at-established voltage ranges. Note the Electrical
Characteristics are referenced with respect to the
LTC4269- 1 package pins.
DETECTION
During detection, the PSE looks for a 25k signature resis-
tor which identifi es the device as a PD. The PSE will apply
two voltages in the range of 2.8V to 10V and measures
the corresponding currents. Figure 1 shows the detection
voltages V1 and V2 and the corresponding PD current. The
PSE calculates the signature resistance using the ΔV/ΔI
measurement technique.
The LTC4269-1 presents its precision, temperature-com-
pensated 25k resistor between the V
pins, alerting the PSE that a PD is present and requests
power to be applied. The LTC4269-1 signature resistor
also compensates for the additional series resistance
introduced by the input diode bridge. Thus a PD built
with the LTC4269-1 conforms to the IEEE 802.3af/IEEE
802.3at specifi cations.
RJ45
+
TX
T1
1
BR1
TX
2
+
RX
TO PHY
3
RX
6
+
SPARE
BR2
4
5
0.1μF
100V
7
8
SPARE
LTC4269-1
PORTP
V
PORTP
LTC4269-1
D3
V
PORTN
42691 F02
and V
PORTN
42691fb
13