D-M9N SMC Corporation, D-M9N Datasheet - Page 92

• Manufacturer Part Number: D-M9N
• Description: Sensor, solid state, direct mount, grommet connection, for MX/MH/CQ2/NCQ2/NCQ8
• Manufacturer: SMC Corporation
• Type: Hall Effectr

Specifications of D-M9N

• Function: Proximity
• Primary Type: Proximity
• Technology: Hall Effect

Auto Switch Mounting Bracket Part No.
(Including bracket, screw)
<Applicable auto switch>
Reed switch······D-90/97, D-90A/93A
How to Mount and Move the Auto Switch
<Applicable auto switch>
Reed switch·················D-A90(V)/A93(V)/A96(V)
Solid state switch········D-M9N(V)/M9P(V)/M9B(V)
How to Mount and Move the Auto Switch
Mounting Bracket
Note) The tightening torque of set screw
CDJP-
Cylinder
series
should be about 0.5 to 0.6 N·m.
„
D
Technical Data 2:
How to Mount and Move the Auto Switch
BP-1
6
Applicable bore size (mm)
• When tightening an auto switch mounting
screw, use a watchmaker’s screwdriver with
a grip diameter of 5 to 6 mm. The tightening
torque should be about 0.1 to 0.2 N·m.
Tie-rod Mounting Style
F9NW(V)/F59W/F9BW(V)
F9BAL
BP-1
10
Set screw
Auto switch
Auto switch
Auto switch mounting bracket
BP-1
15
Set screw
<Applicable auto switch>
Reed switch···············D-E73A/E76A/E80A
Solid state switch······D-M5N/M5P/M5B
1. Insert the auto switch mounting nut into the auto switch mounting
2. Put the convex part of auto switch into the mounting groove and
3. Push the auto switch mounting screw lightly into the mounting nut
4. After reconfirming the detecting position, tighten the mounting screw
Auto Switch Mounting Bracket Part No. (Including nut, screw)
<Applicable auto switch>
Reed switch···············D-Z73/Z76/Z80
Solid state switch······D-Y59 /Y69 , D-Y7P(V)
How to Mount and Move the Auto Switch
How to Mount and Move the Auto Switch
1. Insert the auto switch into the mounting groove and set it at the auto
2. After reconfirming the detecting position, tighten the mounting screw
3. Modification of the detecting position should be made in the
ML1
groove and then set the switch at the mounting position by sliding.
slide it over the nut.
through the mounting hole.
to secure the auto switch. (Tightening torque of M2.5 screw should
be 0.1 to 0.2 N·m.)
Note) When tightening an auto
switch mounting screw, use a
watchmaker’s screwdriver with a
grip diameter of 5 to 6 mm. Also,
set the tightening torque to be
0.05 to 0.1 N·m. As a guide, turn
90° from the position where it
comes to feel tight.
switch mounting position.
to secure the auto switch.
condition of 1.
Cylinder
Auto switch mounting nut
series
M2.5 x 12l
M2.5 x 10l
M2.5 x 10
M2.5 x 12
Auto switch mounting screw
BMY2-025
BMY1-025
25
D-M5NW/M5PW/M5BW
D-M5NTL/M5PTL
D-Y7NW(V)/Y7PW(V)/Y7BW(V)
D-Y7BAL
l
l
(D-E7
(D-M5
Applicable bore size (mm)
„
„
A
B
A/E8
/M5
BMY2-025
BMY1-025
„
„
W/M5
A)
32
Auto switch mounting screw
M2.5 x 4
A
B
„
T)
l
BMY2-025
BMY1-025
6-16-71
40
CJ1
CJP
CJ2
CM2
CG1
MB
MB1
CA2
CS1
C76
C85
C95
CP95
NCM
NCA
D-
-X
20-
Data