MSO-0008P-012 NCC, MSO-0008P-012 Datasheet - Page 19

• Manufacturer Part Number: MSO-0008P-012
• Description: Socket, Relay; 8 Pin Octal
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0008P-012

• Number Of Contacts: 8
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
ORDERING INFORMATION
Delay On Make
Q1F Series
FEATURES
●
●
●
●
●
●
●
●
●
Operating Logic: Upon application of input
voltage, the delay starts. At the end of the
time delay, the load is energized. Reset is
accomplished by removing input voltage.
Note: 1) The load may be located on either side of the line; 2)
Remote potentiometer leads should be shielded when running
close to other wires; 3) The minimum time setting on external
resistor-adjustable time delay relays is obtained by shorting
together the external resistor terminals of the relay; 4) The maxi-
mum time setting within tolerance limits is obtained by using
a 1 megohm resistor; 5) Timing values between the minimum
and maximum limits are linear with resistance within 10%; 6)
Recommend 1/4 W minimum resistor be used.
LOGIC FUNCTION DIAGRAM
Input
Voltage
Load
Optional Potentiometer: Part Number ASY-0001M-450
Reset time, during timing
Reset time, after timeout
Min. load
Max. leakage current
Voltage drop at 1 A
Power consumption, during
timing
Power consumption, after
timeout
Peak 1 cycle surge
Protection
100% functionally tested
Time delays to 10 hours standard
Solid state digital timing
20:1 maximum to minimum timing ratio
Compact size
Low cost
Superior transient protection
Flame-retardant and solvent-resistant
polyester thermoplastic housing
180 to 3600 sec.
15 to 300 sec.
30 to 600 sec.
TIME RANGE
.05 to 1 sec.
.25 to 5 sec.
.5 to 10 sec.
3 to 60 sec.
.25 to 5 hrs.
.5 to 10 hrs.
On
Off
On
Off
Delay On Make Function
File #E65038
Timing
10mA DC, 60 mA AC
12 VAC/DC +10%
Q1F-00001-316
Q1F-00005-316
Q1F-00010-316
Q1F-00060-316
Q1F-00300-316
Q1F-03600-316
Q1F-18000-316
Q1F-36000-316
0.25 VA max.
3.0 VA max.
3.3 V max.
8.8j. MOV
125 ms
10 ms
2 mA
20 A
—
(Series Load)
10mA DC, 40 mA AC
24 VAC/DC +10%
Q1F-00001-317
Q1F-00005-317
Q1F-00010-317
Q1F-00060-317
Q1F-00300-317
Q1F-03600-317
Q1F-18000-317
0.25 VA max.
3.0 VA max.
3.3 V max.
8.8j. MOV
125 ms
10 ms
4 mA
20 A
SPECIFICATIONS
TIME DELAY
Adjustment: External resistor, factory fixed on
special order (min. order requirement)
Range: 50 ms to 10 hours in 9 ranges
Repeatability: ±.5% +8 ms max. (0.25% typical)
at constant temperature
Accuracy: Maximum time ±2% at Rt = 1 meg-
ohms; Minimum time +0%, -30% at Rt = 0 ohm
INPUT
Operating Voltage: 12, 24, 120, 240 VAC/DC
±10% (on DC models, unfiltered supply voltage
must be full-wave rectified)
Frequency: 50/60 Hz
OUTPUT
Type: Solid state, normally open series load
Rating: 1 A steady state max.
Life: 100,000,000 operations
PROTECTION
Transient Voltage: Metal oxide varistor, see rat-
ings below
Dielectric Breakdown: 3000 VAC, RMS, termi-
nals to mounting
Insulation Resistance: 100 megohms min.
between terminals and case
MECHANICAL
Termination: .25” x .032” male fast-on terminals
Mounting: Surface mount with one #8 screw
ENVIRONMENTAL
Storage Temperature: -40°C to 85°C
Operating Temperature: -40°C to 85°C
Humidity: 95% relative
—
—
120 VAC/DC +10%
Q1F-00001-311
Q1F-00005-311
Q1F-00010-311
Q1F-00060-311
Q1F-00300-311
Q1F-00600-311
Q1F-03600-311
Q1F-18000-311
Q1F-36000-311
0.5 VA max.
3.0 VA max.
3.3 V max.
30j. MOV
125 ms
10 mA
10 ms
2 mA
20 A
240 VAC/DC +10%
Q1F-00005-315
Q1F-00300-315
Q1F-03600-315
Q1F-36000-315
0.5 VA max.
3.0 VA max.
3.3 V max.
30j. MOV
125 ms
10 mA
10 ms
2 mA
20 A
—
—
—
—
—
TIME DELAY RELAYS
External Resistance/Time Delay Relationship
1 megohm external resistance is required to obtain
the maximum time for all ranges. To determine the
actual resistance needed to obtain the required time
delay, use the following formula:
Note: Due to component tolerances, the actual time
obtained will normally be within 5% of desired time.
Consult factory for any special requirements not
listed in catalog (minimum order requirement may
apply).
Rt=
Tmaximum - Tminimum
Trequired - Tminimum
VOLTAGE
Rt
INPUT
5
1
.25 X .032 MALE FAST-ON
2.00 SQ.
TERMINALS (4 PL.)
C L
4
1.25
LOAD
.88
(3667-1)
3
L C
x 1,000,000 ohms
.170
DIA.
1-9