MSO-0008P-012 NCC, MSO-0008P-012 Datasheet - Page 24

• Manufacturer Part Number: MSO-0008P-012
• Description: Socket, Relay; 8 Pin Octal
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0008P-012

• Number Of Contacts: 8
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
1-14
Single Shot
T2 Series
FEATURES
●
●
●
●
●
●
●
●
●
●
Operating Logic: Voltage is applied to the
timer at all times. Upon a momentary or
maintained closure of a normally open iso-
lated start switch, the output relay coil is
energized and the time delay starts. At the
end of the preset time delay, the relay coil
is de-energized and the timer is ready for a
new cycle.
Note: 1) Do not apply voltage or ground to the Start switch, 2)
Switch leads should be shielded when running close to other wires
(Start switch supplied by customer)
LOGIC FUNCTION DIAGRAM
Input
Voltage
Start
Switch
Relay
Coil
ORDERING INFORMATION
100% functionally tested
Digital timing circuit
Time delays to 1 hour
±1% repeatability
Superior transient protection
Fiberglass reinforced circuit board
Internal components supported by
heavy-duty chassis
Reinforced locator pin
Flame-retardant and solvent-resistant
polyester thermoplastic housing
36 to 3600 sec.
1.8 to 180 sec.
3 to 300 sec.
6 to 600 sec.
TIME RANGE
.1 to 10 sec.
.3 to 30 sec.
.6 to 60 sec.
Closed
Open
On
Off
On
Off
TIME DELAY RELAYS
File #E59090
Single Shot Function
T2K-00010-466
T2K-00060-466
DPDT RELAY
11-PIN BASE
12 VDC
Timing
—
—
—
—
—
T2K-00010-462
T2K-00060-462
DPDT RELAY
11-PIN BASE
24 VDC
—
—
—
—
—
SPECIFICATIONS
TIME DELAY
Adjustment: Knob, factory fixed on special order
(min. order required)
Range: 100 ms to 1 hour in 7 ranges
Repeatability: ±1% at constant temperature
Accuracy: Maximum time -0%, +10%;
Minimum time +0%, - 50%
Reset Time: 400 ms max.
INPUT
Operating Voltage: 24, 120 VAC; 12, 24 VDC
±10% (DC models have reverse polarity protec-
tion; unfiltered input voltage to them must be full-
wave rectified)
Start Switch Closure Time: 20 ms min.
Power Consumption: 3 VA max.
Frequency: 50/60 Hz
OUTPUT
Type: Relay contacts, SPDT (1 form C) or DPDT;
(2 form C)
Rating: 10 A max. resistive at 240 VAC; 100 mA
at 5 VDC min. load current
Life:
Mechanical: 10,000,000 operations
Full Load: 500,000 operations
PROTECTION
Transient Voltage: 12 and 24 V timers are pro-
tected by an 8.8 joule metal oxide varistor; 120 V
timers are protected by a 30 joule metal oxide
varistor
Dielectric Breakdown: 1500 VAC, RMS min. at
60 Hz between input and outputs and between
outputs
MECHANICAL
Termination: 8-pin or 11-pin plug
Mounting: Socket mount, 8-pin part number
MSO-0008P-012; socket mount, 11-pin part
number MSO-0011P-012
ENVIRONMENTAL
Storage Temperature: -23°C to 70°C
Operating Temperature: -23°C to 55°C
T2K-00010-467
T2K-00060-467
DPDT RELAY
11-PIN BASE
24 VAC
—
—
—
—
—
T2K-00010-441
T2K-00060-441
SPDT RELAY
8-PIN BASE
120 VAC
—
—
—
—
—
T2K-00010-461
T2K-00030-461
T2K-00060-461
T2K-00180-461
T2K-00300-461
T2K-00600-461
T2K-03600-461
DPDT RELAY
11-PIN BASE
120 VAC
Consult factory for any special requirements not
listed in catalog (minimum order requirement may
apply).
.85
PIN CONFIGURATION
PIN CONFIGURATION
2
2
Polarity Shown is
for D.C. Models
3
3
2.90
1
4
Voltage
Voltage
1
4
Input
5
Input
1.75
6
Start Switch
(by Cust.)
5
7
11
8
8
7
6
9
10
Start Switch
(by Cust.)
.53