MSO-0008P-012 NCC, MSO-0008P-012 Datasheet - Page 25

• Manufacturer Part Number: MSO-0008P-012
• Description: Socket, Relay; 8 Pin Octal
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0008P-012

• Number Of Contacts: 8
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
ORDERING INFORMATION
Single Shot
Q2T Series
FEATURES
●
●
●
●
●
●
●
●
●
●
●
Operating Logic: Power is applied to the
timer at all times. Upon a momentary or
maintained closure of a normally open iso-
lated start switch, the output is energized
and the time delay starts. At the end of the
preset time delay, the output is de-ener-
gized and the unit is ready for a new cycle.
Note: 1) Do not apply voltage or ground to the start switch; 2)
Switch leads should be shielded when running close to other
wires. (Start switch supplied by customer.)
Trigger time (start switch
closure)
Reset time
Min. load
Max. leakage current
Voltage drop at 1 A
Power consumption
Peak 1 cycle surge
Protection
100% functionally tested
Solid state digital timing
Time delays to 5 hours standard
20:1 maximum to minimum timing ratio
Cost efficient
Compact size
Superior transient protection
Epoxy encapsulated
Flame-retardant and solvent-resistant
polyester thermoplastic housing
Trimpot on-board with sealed cermet
element
180 to 3600 sec.
15 to 300 sec.
30 to 600 sec.
TIME RANGE
.05 to 1 sec.
.25 to 5 sec.
.5 to 10 sec.
.25 to 5 hrs.
3 to 60 sec.
File #E65038
120 VAC +10%
Q2T-00001-321
Q2T-00005-321
Q2T-00010-321
Q2T-00060-321
Q2T-00300-321
Q2T-00600-321
Q2T-03600-321
Q2T-18000-321
4.3 VA max.
3.3 V max.
30j. MOV
300 ms
200 uA
20 ms
2 mA
20 A
LOGIC FUNCTION DIAGRAM
Input
Voltage
Start
Switch
Load
SPECIFICATIONS
TIME DELAY
Adjustment: On-board Trimpot
Range: 50 ms to 5 hours in 8 ranges
Repeatability: ±.5% +8 ms max. (0.25% typical)
at constant temperature
Accuracy: Maximum time +10%, -0%;
Minimum time -30%. +0%
INPUT
Operating Voltage: 120 VAC ±10%
Frequency: 50/60 Hz
OUTPUT
Type: Solid state, normally open
Rating: 1 A resistive or inductive
Life: 100,000,000 cycles
PROTECTION
Transient Voltage: 30 joule metal oxide varistor
Dielectric Breakdown: 3000 VAC, RMS, termi-
nals to mounting
Insulation Resistance: 100 megohms min.
between terminals and case
MECHANICAL
Termination: .25” x .032” male fast-on terminals
Mounting: Surface mount with one #8 screw
ENVIRONMENTAL
Storage Temperature: -40°C to 85°C
Operating Temperature: -40°C to 65°C
Humidity: 95% relative
Closed
Open
On
Off
On
Off
Single Shot Function
Timing
TIME DELAY RELAYS
Consult factory for any special requirements not
listed in catalog (minimum order requirement may
apply).
START
SWITCH
TIME DELAY
ADJUSTMENT ACCESS
(3667-4)
LOAD
1
.25 X .032 MALE FAST-ON
2.00 SQ.
TERMINALS (5 PL.)
Polarity Shown is
for D.C. Models
C L
2
VOLTAGE
1.25
INPUT
.88
3
L C
1-15
DIA.
.170