MSO-0008P-012 NCC, MSO-0008P-012 Datasheet - Page 32

• Manufacturer Part Number: MSO-0008P-012
• Description: Socket, Relay; 8 Pin Octal
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0008P-012

• Number Of Contacts: 8
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

1-22
AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
Delay On Break
K3 Series
FEATURES
●
●
●
●
●
●
●
●
●
●
●
Operating Logic: Input voltage is applied
to the timer at all times. Upon a closure of
a normally open isolated start switch, the
output relay is activated and remains so
as long as the switch is kept closed. When
the start switch is opened, timing starts. At
the end of the preset time delay, the output
relay is deactivated and the timer is ready
for a new cycle.
Note: 1) Do not apply voltage or ground to the start switch; 2)
Switch leads should be shielded when running close to other
wires; 3) If the start switch is re-closed during timing, the timer
will reset and will not start timing until start switch is opened (Start
switch supplied by customer).
LOGIC FUNCTION DIAGRAM
Input
Voltage
ORDERING INFORMATION
Start
Switch
Relay
Coil
100% functionally tested
No false contact transfer when reset
during timing
Digital timing circuit
Time delays to 5 minutes
Low cost
Compact size
Spade type base
Wide operating temperature range
Fiberglass reinforced circuit board
Polycarbonate, 94V-2 housing material
3 to 300 sec.
TIME RANGE
.1 to 10 sec.
.6 to 60 sec.
Closed
Open
On
Off
On
Off
Delay On Break Function
TIME DELAY RELAYS
File #E59090
Timing
K3K-00010-661
K3K-00060-661
K3K-00300-661
120 VAC
(Retriggerable)
SPECIFICATIONS
TIME DELAY
Adjustment: Knob, factory fixed on special
order (min. order required)
Range: 100 ms to 5 min. in 3 ranges
Repeatability: ±3% at constant temperature
Accuracy:
Maximum time: +10%/-0%
Minimum time: -50%/+0%
Reset Time: 150 ms max.
Start Switch Closure Time: 50 ms to initiate tim-
ing; 100 ms to reset delay during timing
INPUT
Operating Voltage: 120 VAC ±10%
Power Consumption: 3 VA max.
Frequency: 50/60 Hz
OUTPUT
Type: Relay contacts, DPDT (2 form C)
Rating: 10 A max. resistive at 240 VAC 100 mA at
5 VDC min. load current
Life:
Mechanical: 10,000,000 operations
Full Load: 500,000 operations
PROTECTION
Transient Voltage: 120 V timers are protected by
a 5 joule metal oxide varistor
Dielectric Breakdown: 1500 VAC, RMS min. at
60 Hz between input and outputs and between
outputs
MECHANICAL
Termination: Spade (.187” x .020” terminal) type
plug-in base
Mounting: Socket mount, part number
MSO-00KUP-012
ENVIRONMENTAL
Storage Temperature: -23°C to 70°C
Operating Temperature: -23°C to 55°C
Consult factory for any special requirements not
listed in catalog (minimum order requirement may
apply).
.70
Max.
Polarity Shown is
+
4
A
1
7
for D.C. Models
Case 6
Voltage
1.531
(3021-4)
Input
2.125
5
8
Start Switch
.25
(By Cust.)
3
6
-
9
B