MSO-0008P-012 NCC, MSO-0008P-012 Datasheet - Page 36

• Manufacturer Part Number: MSO-0008P-012
• Description: Socket, Relay; 8 Pin Octal
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0008P-012

• Number Of Contacts: 8
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

1-26
AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
Interval
Q4F Series
FEATURES
●
●
●
●
●
●
●
●
●
Operating Logic: Upon application of input
voltage the load energizes and the timing
cycle starts. At the completion of the preset
time delay, the load is de-energized. Reset
is accomplished by removal of input voltage.
Note: 1) Remote potentiometer leads should be shielded when
running close to other wires; 2) The minimum time setting on
external resistor-adjustable time delay relays is obtained by short-
ing together the external resistor terminals of the relay; 3) The
maximum time setting within tolerance limits is obtained by using
a 1 megohm resistor; 4) Timing values between the minimum
and maximum limits are linear with resistance within 10%; 5)
Recommend 1/4 W minimum resistor be used.
LOGIC FUNCTION DIAGRAM
Input
Voltage
Load
ORDERING INFORMATION
Optional Potentiometer: Part Number ASY-0001M-450
Trigger time (start switch closure)
Reset time
Min. load
Max. leakage current
Voltage drop at 1 A
Power consumption
Peak 1 cycle surge
Protection
100% functionally tested
Solid state digital timing
Time delays to 10 hours standard
20:1 maximum to minimum timing ratio
Low cost
Compact size
Superior transient protection
Flame-retardant and solvent-resistant
polyester thermoplastic housing
180 to 3600 sec.
On
Off
On
Off
15 to 300 sec.
30 to 600 sec.
TIME RANGE
.05 to 1 sec.
.25 to 5 sec.
.5 to 10 sec.
3 to 60 sec.
Interval Function
TIME DELAY RELAYS
.25 to 5 hrs.
.5 to 10 hrs.
File #E65038
Timing
rev. V / 8.8j. MOV
Q4F-00001-326
Q4F-00005-326
Q4F-00010-326
Q4F-00060-326
Q4F-00300-326
Q4F-00600-326
Q4F-03600-326
Q4F-36000-326
12 VDC +10%
3.0 W max.
75 ms
75 ms
20 uA
5 mA
2.1 V
4 A
—
24 VAC/DC +10%
Q4F-00005-327
Q4F-00010-327
Q4F-00060-327
Q4F-03600-327
Q4F-18000-327
Q4F-36000-327
3.0 VA max.
8.8j. MOV
SPECIFICATIONS
TIME DELAY
Adjustment: External resistor, factory fixed on
special order (min. order required)
Range: 50 ms to 10 hours in 9 ranges
Repeatability: ±.5% +8 ms max. (0.25% typical)
at constant temperature
Accuracy:
Maximum time ±2% at Rt = 1 megohm
Minimum time +0%-30% at Rt = 0 ohm
INPUT
Operating Voltage: 120, 24 VAC/DC ±10% (DC
models have reverse polarity protection; unfiltered
input voltage to them must be full-wave rectified)
Frequency: 50/60 Hz
OUTPUT
Type: Solid state, normally open
Rating: 1 A steady state
Life: 100,000,000 operations
PROTECTION
Transient Voltage: Metal oxide varistor, see rat-
ings below
Dielectric Breakdown: 3000 VAC, RMS, termi-
nals to mounting
Insulation Resistance: 100 megohms min.
between terminals and case
MECHANICAL
Termination: .25” x .032” male fast-on terminals
Mounting: Surface mount with one #8 screw
ENVIRONMENTAL
Storage Temperature: -40°C to 85°C
Operating Temperature: -40°C to 65°C
Humidity: 95% relative
50 ms
50 ms
20 uA
5 mA
3.2 V
4 A
—
—
—
Q4F-00001-321
Q4F-00005-321
Q4F-00010-321
Q4F-00060-321
Q4F-00300-321
Q4F-00600-321
Q4F-03600-321
Q4F-18000-321
Q4F-36000-321
120 VAC +10%
3.0 VA max.
30j. MOV
150 ms
150 ms
100 uA
2 mA
3.3 V
20 A
Q4F-00001-325
Q4F-00005-325
Q4F-00010-325
Q4F-00600-325
Q4F-36000-325
240 VAC +10%
3.0 VA max.
30j. MOV
150 ms
150 ms
100 uA
2 mA
3.3 V
20 A
—
—
—
—
External Resistance/Time Delay Relationship
1 megohm external resistance is required to obtain
the maximum time for all ranges. To determine the
actual resistance needed to obtain the required time
delay, use the following formula:
Note: Due to component tolerances, the actual time
obtained will normally be within 5% of desired time.
Consult factory for any special requirements not
listed in catalog (minimum order requirement may
apply).
Rt=
Tmaximum - Tminimum
Trequired - Tminimum
Rt
(3667-7)
LOAD
5
1
.25 X .032 MALE FAST-ON
2.00 SQ.
TERMINALS (7 PL.)
Polarity Shown is
for DC Models
4
C L
2
VOLTAGE
1.25
INPUT
.88
3
x 1,000,000 ohms
L C
.170
DIA.