82-4425 M39012/01-0501 AMPHENOL RF, 82-4425 M39012/01-0501 Datasheet
82-4425 M39012/01-0501
Manufacturer Part Number
82-4425 M39012/01-0501
Description
connector, rf coaxial, n straight plug, crimp-crimp, for rg/u 214, 225, 393 cable
Manufacturer
AMPHENOL RF
Type
Cable Plugr
Datasheet
1.82-4425_M3901201-0501.pdf
(1 pages)
Specifications of 82-4425 M39012/01-0501
Angle
Straight
Application
True MIL
Cable Type
RG/U 213,214,225,393,8,9
Contact Plating
Gold
Finish, Housing
Silver
Impedance
50 Ohms
Material, Dielectric
TFE/Styrene
Material, Housing
Brass
Mating Type
Threaded
Primary Type
N
Special Features
Captivated Contact
Termination
Crimp
Voltage, Rating
1500 V
Lead Free Status / Rohs Status
RoHS Compliant part
Assembly Instructions-C11
Type N
CRIMP-CRIMP TYPES
Step 1
Step 2
Step 3
Amphenol Corporation Tel: 800-627-7100
82-332
82-340
82-340-1052
82-340-1054
82-4425
82-4425-1003
82-4426
82-4426-11RFX
82-4426-1001
82-4426-1002
82-4427
82-4427-1006
82-4440
82-4440-1001
82-5370
82-5372
82-5373
82-5374
82-5375
82-5375-RFX
82-5378
82-5933
82-5988-1000
82-5988-1004
82-5993
82-5994
82-5995
82-6010
82-6106
82-5988-1000
82-5988-1004
Amphenol
Number
N Plug
N Plug
N Plug
N Plug
N Plug
N Plug
N Plug
N Plug
N Plug
N Plug
N Plug
N Plug
N Angle Plug
N Angle Plug
N Plug
N Panel Jack
N Bulkh. Jack
N Angle Plug
N Plug
N Plug
N Bulkh. Jack
N Bulkh. Jack
N Angle Plug
N Angle Plug
N Plug
N Bulkh. Jack
N Angle Plug
N Plug
N Plug
N Angle Plug
N Angle Plug
Connector
crimp here
Type
9, 214
8, 213
B9913, 9914
LMR 400
9, 214, 225, 393
9, 214, 225, 393
8, 213
8, 213, 214 Eth.Cables .630(16.0)
Ethernet Cables
Ethernet Cables
142, 400
142, 142B, 400
214, 225, 393
9, 214, 225, 393
55, 142, 223
55, 141, 142
55, 142, 223
55, 142, 223
58, 141
58, 141
58, 141
316
214, 393
214, 393
LMR 600
LMR 600
LMR 600
LMR 240
LMR 240
LMR 240
LMR 240
crimp here
RG-/U
Cable
a
b
.531(13.5)
.531(13.5)
.539(13.7)
.539(13.7)
.687(17.4)
.687(17.4)
.687(17.4)
.687(17.4)
.687(17.4)
.687(17.4)
.600(15.2)
.687(17.4)
.687(17.4)
.600(15.2)
.600(15.2)
.640(16.3)
.687(17.4)
.531(13.5)
.630(16.0)
.640(16.3)
.502(12.7)
.827(21.0)
.827(21.0)
.844(21.4)
.844(21.4)
1.062(27.0)
.610(15.5)
.687(17.4)
.827(21.0)
.827(21.0)
c
outer ferrule
a
Strip Dimensions, inches (mm)
.234(6.0)
.234(6.0)
.250(6.4)
.250(6.4)
.281(7.1)
.281(7.1)
.281(7.1)
.303(7.7)
.281(7.1)
.281(7.1)
.281(7.1)
.275(7.0)
.281(7.1)
.281(7.1)
.275(7.0)
.275(7.0)
.315(8.0)
.281(7.1)
.233(5.9)
.303(7.7)
.273(6.8)
.102(2.6)
.492(12.5)
.492(12.5)
.344(8.7)
.344(8.7)
.562(14.3)
.200(5.1)
.312(7.9)
.492(12.5)
.492(12.5)
Step 1 Strip cable jacket, braid, and dielectric to dimensions shown. All cuts
Step 2 Slide outer ferrule onto cable as shown. Flare slightly end
Step 3 Install cable assembly into body assembly so inner ferrule
b
283
are to be sharp and square. Important: Do not nick braid, dielectric,
and center conductor. Tinning of center conductor is not necessary if
contact is to be crimped. For solder method, tin center conductor
avoiding excessive heat.
of cable braid as shown to facilitate insertion of inner
ferrule. Important: Do not comb out braid.
Place contact on cable center conductor so it butts against
cable dielectric. Center conductor should be visible
through inspection hole in contact. Crimp or solder contact
in place as follows:
Crimp Method: Use Die Set Cavity for contact indicated in
table above.Solder Method: Soft solder contact to cable center
conductor. Do not get any solder on outside surface of
contact. Avoid excessive heat to prevent swelling of dielectric.
portion slides under braid. Push cable assembly forward
until contact snaps into place in insulator. Slide outer ferrule over braid
and up against connector body. Crimp outer ferrule using Die Set
Cavity specified in table above.
contact
.140(3.5)
.141(3.6)
.158(4.0)
.157(4.0)
.187(4.7)
.187(4.7)
.187(4.7)
.157(4.0)
.187(4.7)
.187(4.7)
.187(4.7)
.140(3.5)
.187(4.7)
.187(4.7)
.140(3.5)
.140(3.5)
.180(4.6)
.187(4.7)
.140(3.5)
.157(4.0)
.180(4.6)
.062(1.6)
.157(4.0)
.157(4.0)
.250(6.4)
.250(6.4)
.312(7.9)
.200(5.1)
.187(4.7)
.157(4.0)
.157(4.0)
c
.100(2.5)
.100(2.5)
.116(2.9)
.116(2.9)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
.100(2.5)
Solder
Solder
Solder
.176(4.5)
.176(4.5)
Solder
Press-Fit
.100(2.5)
.100(2.5)
.100(2.5)
Cavity for
Contact
Hex Crimp Data
.429(10.9)
.429(10.9)
.429(10.9)
.429(10.9)
.429(10.9)
.429(10.9)
.429(10.9)
.429(10.9)
.429(10.9)
.429(10.9)
.213(5.4)
.213(5.4)
.429(10.9)
.429(10.9)
.213(5.4)
.213(5.4)
.213(5.4)
.213(5.4)
.213(5.4)
.213(5.4)
.213(5.4)
.178(4.5)
.429(10.9)
.429(10.9)
.612(15.5)
.612(15.5)
.612(15.5)
.255(6.5)
.255(6.5)
.255(6.5)
.255(6.5)
Outer Ferrule
Cavity for
body assembly
Amphenol
227-1221-25
227-1221-25
227-1221-63
227-1221-63
227-1221-25
227-1221-25
227-1221-25
227-1221-25
227-1221-25
227-1221-25
227-1221-57
227-1221-57
227-1221-25
227-1221-25
227-1221-57
227-1221-57
227-1221-57
227-1221-57
227-1221-57
227-1221-57
227-1221-57
227-1221-09
227-1221-6001 CTL-3
227-1221-6001 CTL-3
227-1221-6001 —
227-1221-6001 —
227-1221-6001 —
227-1221-59,-13 CTL-1.5,8
227-1221-59
227-1221-59
227-1221-59
Tool 227-944‡
Die Set for
www.amphenolrf.com
CTL Series
CTL-3
CTL-3
CTL-11
CTL-11
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-3
CTL-2
CTL-5
CTL-5
CTL-5
Tool No.
®
Related parts for 82-4425 M39012/01-0501
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
RF Connectors SMA JACK TO JACK REVERSE POLARITY
Manufacturer:
Amphenol
Datasheet:
Part Number:
Description:
RF Connectors T-ADAPT JCK-PLG-JCK
Manufacturer:
Amphenol
Datasheet:
Part Number:
Description:
RF Connectors R/A JACK TO PLUG
Manufacturer:
Amphenol
Datasheet:
Part Number:
Description:
CONN F SOCKET R/A W/HARDWARE PCB
Manufacturer:
AMPHENOL RF
Datasheet:
Part Number:
Description:
CONN MCX JACK STR 50 OHM SMD
Manufacturer:
AMPHENOL RF
Datasheet:
Part Number:
Description:
CONN BNC JACK R/A 75 OHM PCB
Manufacturer:
AMPHENOL RF
Datasheet: