PIC32MX795F512L-80I/PT Microchip Technology Inc., PIC32MX795F512L-80I/PT Datasheet - Page 137

no-image

PIC32MX795F512L-80I/PT

Manufacturer Part Number
PIC32MX795F512L-80I/PT
Description
512KB Flash, 128KB RAM, 80 MHz, USB, ENET, 2xCAN, 8 DMA
Manufacturer
Microchip Technology Inc.
Datasheet

Specifications of PIC32MX795F512L-80I/PT

A/d Inputs
16-Channel, 10-Bit
Comparators
2
Eeprom Memory
0 Bytes
Input Output
85
Interface
CAN/I2C/SPI/UART/USB
Memory Type
Flash
Number Of Bits
32
Package Type
100-pin TQFP
Programmable Memory
512K Bytes
Ram Size
128K Bytes
Speed
80 MHz
Temperature Range
–40 to +85 °C
Timers
5-16-bit
Voltage, Range
2.3-3.6 V

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC32MX795F512L-80I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC32MX795F512L-80I/PT
Manufacturer:
MICROCHIP
Quantity:
100
Part Number:
PIC32MX795F512L-80I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC32MX795F512L-80I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
1 000
Part Number:
PIC32MX795F512L-80I/PT
0
16.0
FIGURE 16-1:
© 2010 Microchip Technology Inc.
Note 1: This data sheet summarizes the features
Note 1: Where ‘x’ is shown, reference is made to the registers associated with the respective output compare channels,
2: Some registers and associated bits
OUTPUT COMPARE
2: The OCFA pin controls the OC1-OC4 channels. The OCFB pin controls the OC5 channel.
3: Each output compare channel can use one of two selectable 16-bit time bases or a single 32-bit timer base.
of the PIC32MX5XX/6XX/7XX family of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 16. “Output
Capture”
Family Reference Manual” , which is
available from the Microchip web site
(www.microchip.com/PIC32).
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization”
this data sheet for device-specific register
and bit information.
1 through 5.
16
TMR Register Inputs
from Time Bases
Comparator
OUTPUT COMPARE MODULE BLOCK DIAGRAM
OCxRS
0
OCxR
(DS61111) in the “PIC32
(1)
(1)
1
16
(3)
OCTSEL
Period Match Signals
from Time Bases
0
in
1
(3)
Mode Select
OCM<2:0>
The Output Compare module (OCMP) is used to gen-
erate a single pulse or a train of pulses in response to
selected time base events. For all modes of operation,
the OCMP module compares the values stored in the
OCxR and/or the OCxRS registers to the value in the
selected timer. When a match occurs, the OCMP
module generates an event based on the selected
mode of operation.
The following are some of the key features:
• Multiple Output Compare Modules in a device
• Programmable interrupt generation on compare
• Single and Dual Compare modes
• Single and continuous output pulse generation
• Pulse-Width Modulation (PWM) mode
• Hardware-based PWM Fault detection and
• Programmable selection of 16-bit or 32-bit time
• Can operate from either of two available 16-bit
PIC32MX5XX/6XX/7XX
event
automatic output disable
bases
time bases or a single 32-bit time base
Output
3
Logic
Set Flag bit
OCxIF
(1)
Output
Enable
R
S
Q
Output Enable
Logic
OCFA or OCFB
OCx
DS61156F-page 137
(1)
(2)

Related parts for PIC32MX795F512L-80I/PT