DS26303LN-120+ Maxim Integrated Products, DS26303LN-120+ Datasheet - Page 47

• Manufacturer Part Number: DS26303LN-120+
• Description: IC LIU E1/T1/J1 3.3V 144-ELQFP
• Manufacturer: Maxim Integrated Products
• Type: Line Interface Units (LIUs)r

Specifications of DS26303LN-120+

• Number Of Drivers/receivers: 8/8
• Protocol: T1/E1/J1
• Voltage - Supply: 3.135 V ~ 3.465 V
• Mounting Type: Surface Mount
• Package / Case: 144-LQFP Exposed Pad, 144-eLQFP, 144-HLQFP
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

5.1.4 BERT Registers
Register Name:
Register Description:
Register Address:
Bit #
Name
Default
Bit 7: Performance-Monitoring Update Mode (PMUM). When 0, a performance-monitoring update is initiated by
the LPMU register bit. When 1, a performance-monitoring update is initiated by the receive performance-monitoring
update signal (RPMU). Note: If RPMU or LPMU is 1, changing the state of this bit may cause a performance-
monitoring update to occur.
Bit 6: Local Performance-Monitoring Update (LPMU). This bit causes a performance-monitoring update to be
initiated if the local performance-monitoring update is enabled (PMUM = 0). A 0-to-1 transition causes the
performance-monitoring registers to be updated with the latest data, and the counters reset (0 or 1). For a second
performance-monitoring update to be initiated, this bit must be set to 0, and back to 1. If LPMU goes low before the
PMS bit goes high, an update might not be performed. This bit has no affect when PMUM = 1.
Bit 5: Receive New Pattern Load (RNPL). A 0-to-1 transition of this bit causes the programmed test pattern
(QRSS, PTS, PLF[4:0], PTF[4:0], and BSP[31:0]) to be loaded in to the receive pattern generator. This bit must be
changed to 0 and back to 1 for another pattern to be loaded. Loading a new pattern forces the receive pattern
generator out of the sync state, which causes a resynchronization to be initiated. Note: QRSS, PTS, PLF[4:0],
PTF[4:0], and BSP[31:0] must not change from the time this bit transitions from 0 to 1 until four RXCK clock cycles
after this bit transitions from 0 to 1.
Bit 4: Receive Pattern Inversion Control (RPIC). When 0, the receive incoming data stream is not altered. When
1, the receive incoming data stream is inverted.
Bit 3: Manual Pattern Resynchronization (MPR). A 0-to-1 transition of this bit causes the receive pattern
generator to resynchronize to the incoming pattern. This bit must be changed to 0 and back to 1 for another
resynchronization to be initiated. Note: A manual resynchronization forces the receive pattern generator out of the
sync state.
Bit 2: Automatic Pattern Resynchronization Disable (APRD). When 0, the receive pattern generator
automatically resynchronizes to the incoming pattern if six or more times during the current 64-bit window the
incoming data stream bit and the receive pattern generator output bit did not match. When 1, the receive pattern
generator does not automatically resynchronize to the incoming pattern. Note: Automatic synchronization is
prevented by not allowing the receive pattern generator to automatically exit the sync state.
Bit 1: Transmit New Pattern Load (TNPL). A 0-to-1 transition of this bit causes the programmed test pattern
(QRSS, PTS, PLF[4:0], PTF[4:0], and BSP[31:0]) to be loaded in to the transmit pattern generator. This bit must be
changed to zero and back to one for another pattern to be loaded. Note: QRSS, PTS, PLF[4:0], PTF[4:0], and
BSP[31:0] must not change from the time this bit transitions from 0 to 1 until four TXCK clock cycles after this bit
transitions from 0 to 1.
Bit 0: Transmit Pattern Inversion Control (TPIC). When 0, the transmit outgoing data stream is not altered.
When 1, the transmit outgoing data stream is inverted.
PMUM
7
0
LPMU
6
0
BCR
BERT Control Register
00h
RNPL
5
0
DS26303: 3.3V, T1/E1/J1, Short-Haul, Octal Line Interface Unit
47 of 101
RPIC
4
0
MPR
3
0
APRD
2
0
TNPL
1
0
TPIC
0
0