HEDS-5645-I13 Avago Technologies US Inc., HEDS-5645-I13 Datasheet - Page 7

no-image

HEDS-5645-I13

Manufacturer Part Number
HEDS-5645-I13
Description
Encoder; Optical; 3 Channel; 512 CPR; 8 mm Metal CW; Vol-Sup 5 V; 5 Pin Connector
Manufacturer
Avago Technologies US Inc.
Datasheet

Specifications of HEDS-5645-I13

Temperature, Operating, Maximum
100 °C
Temperature, Operating, Minimum
0 °C
Voltage, Supply
5 V
Lead Free Status / Rohs Status
RoHS Compliant part Electrostatic Device
Mechanical Characteristics
Notes:
1. These are tolerances required of the user.
2. The HEDS-55X5 and 56X5, HEDM-5505, 5605 provide an 8.9 mm (0.35 inch) diameter hole through the housing for longer motor
shafts. See Ordering Information.
3. The HEDS-5540 and 5640 must be aligned using the aligning pins as specified in Figure 3, or using the alignment tool as shown in
“Encoder Mounting and Assembly”. See also “Mounting Considerations.”
4. The recommended mounting screw torque for 2 screw and external ear mounting is 1.0 kg-cm (0.88 in-lbs). The recommended
mounting screw torque for 3 screw mounting is 0.50 kg-cm (0.43 in-lbs).
Electrical Interface
To insure reliable encoding
performance, the HEDS-5540 and
5640 three channel encoders
require 2.7 k
resistors on output pins 2, 3, and
5 (Channels I, A, and B) as shown
in Figure 1. These pull-up
resistors should be located as
Codewheel Fits These
Standard Shaft Diameters
Moment of Inertia
Required Shaft Length
Bolt Circle
Mounting Screw Size
Encoder Base Plate
Thickness
Hub Set Screw
Parameter
[3]
( 10%) pull-up
[4]
[2]
mounting ears
mounting ears
mounting
mounting
mounting
mounting
Symbol
external
external
2 screw
3 screw
2 screw
3 screw
close to the encoder as possible
(within 4 feet). Each of the three
encoder outputs can drive a single
TTL load in this configuration.
The HEDS-5500, 5600, and
HEDM-5500, 5600 two channel
encoders do not normally require
pull-up resistors. However, 3.2 k
J
M 2.5 or (2-56)
M 1.6 or (0-80)
M 2.5 or (2-56)
0.6 (8.0 x 10
0.33 (0.130)
Dimension
14.0 (0.55)
5/32 1/8
3/16 1/4
2 3 4
5 6 8
(0.750)
(0.823)
(1.811)
(2-56)
19.05
20.90
46.0
-6
)
Tolerance
7
pull-up resistors on output pins 3
and 5 (Channels A and B) are
recommended to improve rise
times, especially when operating
above 100 kHz frequencies.
( 0.005)
( 0.005)
( 0.005)
+0.0000
( 0.02)
+0.000
-0.0007
-0.015
0.13
0.13
0.13
0.5
[1]
g-cm
mm (in.)
mm (in.)
mm (in.)
mm (in.)
Units
2
(in.)
(in.)
(in.)
(in.)
(in.)
mm
mm
mm
mm
mm
(oz-in-s
in
2
)

Related parts for HEDS-5645-I13