DSPIC33FJ128MC706-I/PT Microchip Technology Inc., DSPIC33FJ128MC706-I/PT Datasheet - Page 320

• Manufacturer Part Number: DSPIC33FJ128MC706-I/PT
• Description: 16 BIT MCU/DSP 64LD 40MIPS 128KB FLASH
• Manufacturer: Microchip Technology Inc.
• Type: DSPr

Specifications of DSPIC33FJ128MC706-I/PT

• A/d Inputs: 16-Channels, 12-Bit
• Comparators: 8
• Cpu Speed: 40 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 53
• Interface: CAN/I2C/SPI/UART
• Ios: 53
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 64-pin TQFP
• Programmable Memory: 128K Bytes
• Ram Size: 16K Bytes
• Timers: 9-16-bit, 4-32-bit
• Voltage, Range: 3-3.6
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

FIGURE 26-2:
TABLE 26-15: EXTERNAL CLOCK TIMING REQUIREMENTS
© 2006 Microchip Technology Inc.
AC CHARACTERISTICS
OS10
OS20
OS25
OS30
OS31
OS40
OS41
Legend: TBD = To Be Determined
Note 1:
Param
No.
OSC1
CLKO
2:
3:
F
T
T
TosL,
TosH
TosR,
TosF
TckR
TckF
Symb
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only
and are not tested.
Instruction cycle period (T
are based on characterization data for that particular oscillator type under standard operating conditions
with the device executing code. Exceeding these specified limits may result in an unstable oscillator
operation and/or higher than expected current consumption. All devices are tested to operate at “min.”
values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the
“max.” cycle time limit is “DC” (no clock) for all devices.
Measurements are taken in EC mode. The CLKO signal is measured on the OSC2 pin.
OSC
CY
IN
External CLKI Frequency
(External clocks allowed only
in EC and ECPLL modes)
Oscillator Crystal Frequency
T
Instruction Cycle Time
External Clock in (OSC1)
High or Low Time
External Clock in (OSC1)
Rise or Fall Time
CLKO Rise Time
CLKO Fall Time
OSC
EXTERNAL CLOCK TIMING
= 1/F
OS41
Characteristic
OSC
(3)
Q1
(3)
CY
OS20
) equals two times the input oscillator time-base period. All specified values
(2)
Q2
Preliminary
Q3
Standard Operating Conditions: 2.5V to 3.6V
(unless otherwise stated)
Operating temperature
0.625 x T
OS40
12.5
Min
0.8
Q4
10
10
25
—
—
—
4
3
3
OS25
OSC
OS30
Q1
Typ
—
—
—
—
—
—
—
—
—
—
—
6
6
OS30
(1)
Q2
-40°C T
TBD
TBD
TBD
Max
DC
DC
64
10
10
40
40
33
—
Q3
8
OS31
A
Units
Q4
MHz
MHz
MHz
MHz
MHz
MHz
kHz
ns
ns
ns
ns
ns
ns
OS31
+85°C for Industrial
dsPIC33F
EC
ECPLL
XT
XTPLL
HS
HSPLL
SOSC
EC
EC
DS70165D-page 317
Conditions