DSPIC33FJ128MC706-I/PT Microchip Technology Inc., DSPIC33FJ128MC706-I/PT Datasheet - Page 69

no-image

DSPIC33FJ128MC706-I/PT

Manufacturer Part Number
DSPIC33FJ128MC706-I/PT
Description
16 BIT MCU/DSP 64LD 40MIPS 128KB FLASH
Manufacturer
Microchip Technology Inc.
Type
DSPr
Datasheet

Specifications of DSPIC33FJ128MC706-I/PT

A/d Inputs
16-Channels, 12-Bit
Comparators
8
Cpu Speed
40 MIPS
Eeprom Memory
0 Bytes
Input Output
53
Interface
CAN/I2C/SPI/UART
Ios
53
Memory Type
Flash
Number Of Bits
16
Package Type
64-pin TQFP
Programmable Memory
128K Bytes
Ram Size
16K Bytes
Timers
9-16-bit, 4-32-bit
Voltage, Range
3-3.6
Lead Free Status / Rohs Status
RoHS Compliant part Electrostatic Device

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DSPIC33FJ128MC706-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC33FJ128MC706-I/PT
Manufacturer:
ST
0
Company:
Part Number:
DSPIC33FJ128MC706-I/PT
Quantity:
36
3.2.7
In addition to its use as a working register, the W15
register in the dsPIC33F devices is also used as a soft-
ware Stack Pointer. The Stack Pointer always points to
the first available free word and grows from lower to
higher addresses. It pre-decrements for stack pops and
post-increments for stack pushes, as shown in
Figure 3-6. For a PC push during any CALL instruction,
the MSb of the PC is zero-extended before the push,
ensuring that the MSb is always clear.
The Stack Pointer Limit register (SPLIM) associated
with the Stack Pointer sets an upper address boundary
for the stack. SPLIM is uninitialized at Reset. As is the
case for the Stack Pointer, SPLIM<0> is forced to ‘0’
because all stack operations must be word-aligned.
Whenever an EA is generated using W15 as a source
or destination pointer, the resulting address is
compared with the value in SPLIM. If the contents of
the Stack Pointer (W15) and the SPLIM register are
equal and a push operation is performed, a stack error
trap will not occur. The stack error trap will occur on a
subsequent push operation. Thus, for example, if it is
desirable to cause a stack error trap when the stack
grows beyond address 0x2000 in RAM, initialize the
SPLIM with the value 0x1FFE.
Similarly, a Stack Pointer underflow (stack error) trap is
generated when the Stack Pointer address is found to
be less than 0x0800. This prevents the stack from
interfering with the Special Function Register (SFR)
space.
A write to the SPLIM register should not be immediately
followed by an indirect read operation using W15.
FIGURE 3-6:
© 2006 Microchip Technology Inc.
0x0000
Note:
15
000000000
SOFTWARE STACK
A PC push during exception processing
concatenates the SRL register to the MSb
of the PC prior to the push.
<Free Word>
PC<15:0>
PC<22:16>
CALL STACK FRAME
0
POP : [--W15]
PUSH : [W15++]
W15 (before CALL)
W15 (after CALL)
Preliminary
3.2.8
The dsPIC33F product family supports Data RAM pro-
tection features which enable segments of RAM to be
protected when used in conjunction with Boot and
Secure Code Segment Security. BSRAM (Secure RAM
segment for BS) is accessible only from the Boot Seg-
ment Flash code when enabled. SSRAM (Secure RAM
segment for RAM) is accessible only from the Secure
Segment Flash code when enabled. See Table 3-1 for
an overview of the BSRAM and SSRAM SFRs.
3.3
The addressing modes in Table 3-35 form the basis of
the addressing modes optimized to support the specific
features of individual instructions. The addressing
modes provided in the MAC class of instructions are
somewhat different from those in the other instruction
types.
3.3.1
Most file register instructions use a 13-bit address field
(f) to directly address data present in the first 8192
bytes of data memory (Near Data Space). Most file
register instructions employ a working register, W0,
which is denoted as WREG in these instructions. The
destination is typically either the same file register or
WREG (with the exception of the MUL instruction),
which writes the result to a register or register pair. The
MOV instruction allows additional flexibility and can
access the entire data space.
3.3.2
The 3-operand MCU instructions are of the form:
Operand 3 = Operand 1 <function> Operand 2
where Operand 1 is always a working register (i.e., the
addressing mode can only be register direct) which is
referred to as Wb. Operand 2 can be a W register,
fetched from data memory, or a 5-bit literal. The result
location can be either a W register or a data memory
location.
supported by MCU instructions:
• Register Direct
• Register Indirect
• Register Indirect Post-Modified
• Register Indirect Pre-Modified
• 5-bit or 10-bit Literal
Note:
Instruction Addressing Modes
The
DATA RAM PROTECTION FEATURE
FILE REGISTER INSTRUCTIONS
MCU INSTRUCTIONS
Not all instructions support all the
addressing modes given above. Individual
instructions may support different subsets
of these addressing modes.
following
addressing
dsPIC33F
DS70165D-page 67
modes
are

Related parts for DSPIC33FJ128MC706-I/PT