ZB-2551 ICP, ZB-2551 Datasheet

Page 1

... At present, the ICP DAS ZigBee converter ZB-2550 and ZB-2551, supports the interfaces. The main design goal is limited data communication using provide a better solution for environments where wiring is difficult. ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---3 RS-232 and wireless transmission, so may RS-485 ...

Page 2

... The typical transmission range of the ICP DAS Zigbee ZB-2550/ZB-2551 converter is 100m, and the ZB-2550P/ZB-2551P is ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---4 RS-485/RS-232 interfaces to be ZigBee router is responsible for 700m. which ...

Page 3

... Pan IDs (65535 network groups can be set). The ZigBee converter includes a repeater module that can be used to increase communication range or prevent data loss if the connection is interrupted or becomes unstable. Please refer to ZigBee converter other document for more information as following links: http://ftp.icpdas.com/pub/cd/usbcd/napdos/zigbee/zigbee_converter/ ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---5 ...

Page 4

... Pin Assignment ZB-2050(P)/ZB-2051(P) ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---6 ...

Page 5

... Specifications RF channels ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---7 ZB-2550P ZB-2550P ZB-2551P ZB-2551P ...

Page 6

... ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---8 ZB-2550P ZB-2551P ...

Page 7

... Block Diagram ZB-2050/ZB-2551 ZB-2050P/ZB-2551P ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---9 ...

Page 8

... Wire Connection Serial Port - RS-232 ZB-2550(P) RS-232 (Female) ZB-2551(P) RS-232 (Male) ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---10 CA-0915 CA-0910N Controller Remote I/O ...

Page 9

... Serial Port - RS-485 ZB-2550(P) ZB-2551(P) ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---11 RS-485 (D+, D GND +10~+ Remote I/O RS-485 (D+, D +10~+30 V GND DC Controller ...

Page 10

... Before configuring the ZigBee converter, adjust the switch to the ZBSET position then re-boot (power off/on) the module. After configuration is complete, adjust the switch to the position then re-boot (power off/on) the module When the following screen is displayed, click on the ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---12 RUN OK button 2 ...

Page 11

... Click on the Connect 3 4. Please select the COM Port ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---13 button on your PC 4 ...

Page 12

... Click on the Config button Converter - ZB-2550(P)/ZB-2551(P). e.g : ZB-2551( Click on the Config button for set the new ZigBee 6 ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---14 to configure setting for the ZigBee setting. ...

Page 13

... RUN position then re-boot (power off/on) the data. Make it work for you Click Default button to load factory default parameters if you want to load factory default setting of ZigBee Module 8 ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---15 module. Leverage the power of your ...

Page 14

... Note : A Work Network - Runing on the same Network Survival Detecting Time ZB-2551(P) will connect with Parent (ZB-2550(P)) periodically to confirm the survival of network detects unsuccessfully, and it process initialize network again to find a new parent. ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---16 Pan ID and RF Channel ...

Page 15

... Default settings for the ZB-2550 are as follows： ： ： ： ZB Node ID： ZB Pan ID： ZB Channel (RF Channel)： ZBSET Data Format： Operating Mode： Default settings for the ZB-2551 are as follows： ： ： ： ZB Node ID：  ZB Pan ID：  ZB Channel (RF Channel)： ...

Page 16

... Technical Support If you have problems about using the ZB-2000 series modules, please contact ICP DAS Product Support. Email: Service@icpdas.com ZB-2550(P)/ZB-2551(P) User Manual Ver1.0, March /200 9 ---25 ...