PIC16F688-I/SL Microchip Technology Inc., PIC16F688-I/SL Datasheet - Page 29

no-image

PIC16F688-I/SL

Manufacturer Part Number
PIC16F688-I/SL
Description
14 PIN, 7 KB FLASH, 256 RAM, 12 I/O
Manufacturer
Microchip Technology Inc.
Datasheet

Specifications of PIC16F688-I/SL

A/d Inputs
8-Channel, 10-Bit
Comparators
2
Cpu Speed
5 MIPS
Eeprom Memory
256 Bytes
Input Output
12
Interface
USART
Memory Type
Flash
Number Of Bits
8
Package Type
14-pin SOIC-N
Programmable Memory
7K Bytes
Ram Size
256 Bytes
Speed
20 MHz
Timers
1-8-bit, 1-16-bit
Voltage, Range
2-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part Electrostatic Device

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC16F688-I/SL
Manufacturer:
MICROCHIP
Quantity:
4 952
Part Number:
PIC16F688-I/SL
Manufacturer:
Microchip Technology
Quantity:
27 564
Part Number:
PIC16F688-I/SL
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC16F688-I/SL
0
3.5.3
The Low-Frequency Internal Oscillator (LFINTOSC) is
an uncalibrated 31 kHz internal clock source.
The output of the LFINTOSC connects to a postscaler
and multiplexer (see Figure 3-1). Select 31 kHz, via
software, using the IRCF<2:0> bits of the OSCCON
register. See Section 3.5.4 “Frequency Select Bits
(IRCF)” for more information. The LFINTOSC is also the
frequency for the Power-up Timer (PWRT), Watchdog
Timer (WDT) and Fail-Safe Clock Monitor (FSCM).
The LFINTOSC is enabled by selecting 31 kHz
(IRCF<2:0> bits of the OSCCON register = 000) as the
system clock source (SCS bit of the OSCCON
register = 1), or when any of the following are enabled:
• Two-Speed Start-up IESO bit of the Configuration
• Power-up Timer (PWRT)
• Watchdog Timer (WDT)
• Fail-Safe Clock Monitor (FSCM)
The LF Internal Oscillator (LTS) bit of the OSCCON
register indicates whether the LFINTOSC is stable or
not.
3.5.4
The output of the 8 MHz HFINTOSC and 31 kHz
LFINTOSC connects to a postscaler and multiplexer
(see Figure 3-1). The Internal Oscillator Frequency
Select bits IRCF<2:0> of the OSCCON register select
the frequency output of the internal oscillators. One of
eight frequencies can be selected via software:
• 8 MHz
• 4 MHz (Default after Reset)
• 2 MHz
• 1 MHz
• 500 kHz
• 250 kHz
• 125 kHz
• 31 kHz (LFINTOSC)
© 2006 Microchip Technology Inc.
Word register = 1 and IRCF<2:0> bits of the
OSCCON register = 000
Note:
LFINTOSC
FREQUENCY SELECT BITS (IRCF)
Following any Reset, the IRCF<2:0> bits of
the OSCCON register are set to ‘110’ and
the frequency selection is set to 4 MHz.
The user can modify the IRCF bits to
select a different frequency.
3.5.5
When switching between the LFINTOSC and the
HFINTOSC, the new oscillator may already be shut
down to save power (see Figure 3-6). If this is the case,
there is a delay after the IRCF<2:0> bits of the
OSCCON register are modified before the frequency
selection takes place. The LTS and HTS bits of the
OSCCON register will reflect the current active status
of the LFINTOSC and HFINTOSC oscillators. The
timing of a frequency selection is as follows:
1.
2.
3.
4.
5.
6.
See Figure 3-1 for more details.
If the internal oscillator speed selected is between
8 MHz and 125 kHz, there is no start-up delay before
the new frequency is selected. This is because the old
and new frequencies are derived from the HFINTOSC
via the postscaler and multiplexer.
Start-up delay specifications are located in the
Section 14.0 “Electrical Specifications”, under the
AC Specifications (Oscillator Module).
IRCF<2:0> bits of the OSCCON register are
modified.
If the new clock is shut down, a clock start-up
delay is started.
Clock switch circuitry waits for a falling edge of
the current clock.
CLKOUT is held low and the clock switch
circuitry waits for a rising edge in the new clock.
CLKOUT is now connected with the new clock.
LTS and HTS bits of the OSCCON register are
updated as required.
Clock switch is complete.
HF AND LF INTOSC CLOCK
SWITCH TIMING
PIC16F688
DS41203C-page 27

Related parts for PIC16F688-I/SL