JM38510/19007BEA Intersil, JM38510/19007BEA Datasheet - Page 10

• Manufacturer Part Number: JM38510/19007BEA
• Description: Analog Multiplexer Single 8:1 16-Pin CDIP
• Manufacturer: Intersil
• Type: Analog Multiplexerr

Specifications of JM38510/19007BEA

• Package: 16CDIP
• Maximum On Resistance: 300@±15V Ohm
• Maximum Propagation Delay Bus To Bus: 500@±15V ns
• Maximum High Level Output Current: 20 mA
• Multiplexer Architecture: 8:1
• Power Supply Type: Single|Dual

DSCC FORM 2234
APR 97
1/ For device types 01 and 02, V
2/ Input current of one input mode.
3/ Guaranteed, if not tested, to the limits specified.
in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN
number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535,
appendix A and the requirements herein.
with each lot of microcircuits delivered to this drawing.
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
Propagation delay times:
Address inputs to I/O
Enable to I/O
channels times:
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
device types 04, 05, 06, 07, 08 and 09, V
flowing in either direction between any associated input and output terminals of the switch shall be 30 mA.
DEFENSE SUPPLY CENTER COLUMBUS
Test
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
STANDARD
t
t
Symbol
t
OFF(EN)
t
ON(EN)
OFF(A)
ON(A)
REF
TABLE I. Electrical performance characteristics - continued.
,
= open. For device types 01, 02, and 03, V
,
R
see figure 4
R
see figure 4
R
see figure 4
R
See figure 4
unless otherwise specified
L
L
L
L
EN
= 1 kΩ, C
= 10 kΩ, C
= 1 kΩ, C
= 1 kΩ, C
-V = -15 V, +V = +15 V
-55°C ≤ T
= 2.4 V unless otherwise specified. For device types 04, 05, and 06, current
Conditions 1/
L
L
L
A
L
= 100 pF,
= 100 pF,
= 50 pF,
≤ +125°C
= 50 pF,
SIZE
A
subgroups
Group A
10, 11
10, 11
10, 11
10, 11
9
9
9
9
EN
REVISION LEVEL
= 4.0 V unless otherwise specified. For
Device
01, 02,
01, 02,
03, 07,
04, 05,
03, 07,
04, 05,
07,08,
08, 09
01,02,
08, 09
type
03
09
06
06
F
Min
Limits
1,000
1,000
1,500
1,000
1,000
Max
SHEET
750
500
500
700
5962-85131
10
Unit
ns
ns