MAX8631XETI Maxim Integrated Products, MAX8631XETI Datasheet
MAX8631XETI
Specifications of MAX8631XETI
Available stocks
Related parts for MAX8631XETI
MAX8631XETI Summary of contents
Page 1
... Thermal T ♦ Low Input Ripple and EMI ♦ 2.7V to 5.5V Supply Voltage Range Applications ♦ Soft-Start, Overvoltage, and Thermal-Shutdown Protection ♦ 28-Pin Thin QFN, 4mm x 4mm Package PART MAX8631XETI+ MAIN FLASH MAX8631YETI Exposed pad. + Denotes a lead-free package. CAMERA MODULE 1μF Pin Configuration appears at end of data sheet ...
Page 2
White LED Charge Pump with Two LDOs in 4mm x 4mm Thin QFN ABSOLUTE MAXIMUM RATINGS PIN, IN, OUT, REFBP to GND................................-0.3V to +6.0V SETF, SETM, ENLDO, ENM1, ENM2, ENF, P1, P2, LDO1, LDO2 to GND....................-0. M1, ...
Page 3
White LED Charge Pump with Two ELECTRICAL CHARACTERISTICS (continued 3.6V 0V, ENM1 = ENM2 = ENF = IN GND PGND T = -40°C to +85°C, unless otherwise noted. Typical values are ...
Page 4
White LED Charge Pump with Two LDOs in 4mm x 4mm Thin QFN ELECTRICAL CHARACTERISTICS (continued 3.6V 0V, ENM1 = ENM2 = ENF = IN GND PGND T = -40°C to ...
Page 5
White LED Charge Pump with Two LDOs in 4mm x 4mm Thin QFN ( 3.6V, circuit of Figure EN_ BATTERY CURRENT vs. SUPPLY VOLTAGE DRIVING FLASH 900 800 700 I = 400mA FLASH ...
Page 6
White LED Charge Pump with Two LDOs in 4mm x 4mm Thin QFN ( 3.6V, Circuit of Figure EN_ INDIVIDUAL FLASH LED CURRENT vs. R 1000 100 SETF ...
Page 7
White LED Charge Pump with Two ( 3.6V, circuit of Figure EN_ SINGLE-WIRE DIMMING RESPONSE V ENM1, V ENM2 I OUT V OUT 10ms/div LDO OUTPUT VOLTAGE ACCURACY vs. OUTPUT CURRENT 1.0 0.8 ...
Page 8
White LED Charge Pump with Two LDOs in 4mm x 4mm Thin QFN INPUT C1P 2.7V TO 5.5V PIN IN C1 10μF GND PGND REFBP C8 0.01μF CONTROL AND ENM1 REFERENCE ENM2 0.15V ENF FLASH CONTROL MAIN CONTROL ENLDO ...
Page 9
White LED Charge Pump with Two PIN NAME Supply Voltage Input. Bypass to PGND with a 10µF ceramic capacitor. The input voltage range is 1 PIN 2.7V to 5.5V. PIN is high impedance during shutdown. Chip Supply Voltage Input. ...
Page 10
... MAX8631X/Y starts switching in 2x mode. When the input voltage rises above two-thirds V by approximately 50mV, OUT the MAX8631X/Y switches back to 1.5x mode. True Shutdown is a trademark of Maxim Integrated Products, Inc. 10 ______________________________________________________________________________________ Pin Description (continued) FUNCTION The MAX8631X/Y includes soft-start circuitry to limit inrush current at turn-on ...
Page 11
White LED Charge Pump with Two INITIAL t HI ≥ 200μ ENM1 AND ENM2 OR t SOFT-START ENF 32/32 31/ SHUTDOWN Figure 2. ENM_ and ENF Timing Diagram Thermal Shutdown The MAX8631X/Y ...
Page 12
White LED Charge Pump with Two LDOs in 4mm x 4mm Thin QFN INPUT 2.7V TO 5.5V 10μF MAIN ON/OFF AND DIMMING FLASH ON/OFF AND DIMMING ON/OFF VOLTAGE SELECTION Figure 3. Dimming Using Single-Wire, Serial-Pulse Interface INPUT 2.7V TO ...
Page 13
White LED Charge Pump with Two INPUT 2.7V TO 5.5V 10μF ON/OFF AND VOLTAGE SELECTION Figure 5. Schematic for When Fewer than 8 LEDs Is Acceptable Typical operating waveforms shown in the Typical Operating Characteristics show input ripple current ...
Page 14
... X7R ceramic capacitor (0402) Nichia NSCW215T White LEDs Nichia NBCW011T White LEDs, 4 LEDs in one package — 1% resistor Vishay TOP VIEW C1P PGND DOCUMENT NO. 21-0139 P1 DESCRIPTION Pin Configuration MAX8631XETI MAX8631YETI THIN QFN 4mm x 4mm, 0.4mm LEAD PITCH SETM ...
Page 15
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 15 © 2008 Maxim Integrated Products ...