48XBRMR120A EDWARDS SIGNALING PRODUCTS, 48XBRMR120A Datasheet
48XBRMR120A
Manufacturer Part Number
48XBRMR120A
Description
LED BEACON, 120VAC, 108MA
Manufacturer
EDWARDS SIGNALING PRODUCTS
Datasheet
1.48XBRMA120A.pdf
(4 pages)
Specifications of 48XBRMR120A
Light Source
LED
Current Rating
108mA
Flash Rate Per Minute
65
Ip/nema Rating
NEMA 4X
Lens Color
Red
Supply Voltage
120VAC
Description
The Catalog Series 48XBRM Visual Indicator is a UL and cUL
Listed signaling appliance rated for NEMA 4X applications.
The signals are suitable for indoor or outdoor (weatherproof)
installation and are available in AC and DC models as listed
above.
The 48XBRM Series XBR (XTRA-BRITE
signals are well suited in high ambient noise level areas,
especially where ear protection must be worn. These LED
beacons are also ideal for high-vibration applications and
areas where long lamp life is advantageous. 48XBRM LED
beacons ship from the factory in steady-on mode and can
be readily transformed by changing the dipswitch setting to
65 FPM flashing mode.
The 48XBRM series signals can be mounted on 1/2" (13mm)
NPT conduit (indoor or outdoor) or direct surface mounted
(indoor only). For outdoor (weatherproof) installation, the
signals must be mounted with their lens dome facing directly
up. When installing indoors, these signals can be mounted
in any position.
Electrical Specifications
Mechanical Specifications
Outdoor Locations
Temperature Ratings ........... -31F to +150F (-35C to +66C)
Catalog Number
48XBRMA24D
48XBRMA120A
48XBRMB24D
48XBRMB120A
48XBRMG24D
48XBRMG120A
48XBRMR24D
48XBRMR120A
48XBRMW24D
48XBRMW120A
*120V AC 50/60 Hz
120V AC*, 0.108A
120V AC*, 0.108A
120V AC*, 0.108A
120V AC*, 0.108A
120V AC*, 0.108A
24V DC, 0.215A
24V DC, 0.215A
24V DC, 0.215A
24V DC, 0.215A
24V DC, 0.215A
Electrical Specs
http://www.edwardssignaling.com Phone: (800) 336-4206 Fax: (800) 454-2363
XBR (XTRA-BRITE
TM
) LED Dual-Mode
Installation Instructions for 48XBRM Series
Amber
Amber
Green
Green
White
White
Color
Blue
Blue
Red
Red
PLC Compatibility
Signaling devices may be directly connected to PLC output
cards that meet the electrical input load specifications listed
in Table 1. When signaling device flash rates are to be con-
trolled via PLC, dip switch settings should be left in "steady-
on" mode as originally shipped from the factory.
Installation
Install in accordance with the latest edition of the National
Electrical Code and local regulations. Install the signals
using one of the following applicable mounting procedures.
Conduit Mounting (Indoor or Outdoor) - Figure 1
1. Insert a small flat blade screwdriver between the locking
2. Setting the Flash Pattern: The 48XBRM Series Visual
3. After setting the flash pattern, carefully place the lens
4. Route the signal's wire leads through 1/2" NPT conduit
5. Connect the field wiring to the signal wire leads as
mechanism and the lens. Gently push down and then
pry up, unseating the lens. Pull the lens up and off of
the signal mounting base, being careful not to damage
the internal circuit.
Indicator is a dual-mode device supplied with a default
setting of steady-on. If flashing (65 fpm) mode is desired,
set dipswitch as shown in Figure 4. Refer to Figure 3 for
dipswitch location.
back on the unit and snap in place.
(not supplied) and thread the conduit into the signal
mounting base.
described in the Wiring Section.
TM
Indicator
WARNING
WARNING
To prevent electrical shock, ensure that power
is disconnected before installing the signals.
To prevent leakage and a potential shock
hazard, when mounting outdoors the signal
must be installed with the lens or dome facing
directly up.
) LED DUAL-MODE Visual
P/N 3101569 ISSUE 3
© 2010
Related parts for 48XBRMR120A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PUSH BUTTON 821 EDCAN
Manufacturer:
EDWARDS SIGNALING PRODUCTS
Datasheet:
Part Number:
Description:
#6 X 3/4 L TAMPRUFœ ROUNDHEAD
Manufacturer:
EDWARDS SIGNALING PRODUCTS
Part Number:
Description:
,MAGIC CONTACT,OVERHEAD DOOR,F
Manufacturer:
EDWARDS SIGNALING PRODUCTS
Part Number:
Description:
CAST BACK BOX FOR 6 IN/10 IN 340 BELLS
Manufacturer:
EDWARDS SIGNALING PRODUCTS
Part Number:
Description:
TRANSFORMER 120V AC 50/60 HZ PRIMARY, 24V AC 40 VA SECONDARY
Manufacturer:
EDWARDS SIGNALING PRODUCTS
Part Number:
Description:
RARE EARTH STANDARD GAP MAG,(O
Manufacturer:
EDWARDS SIGNALING PRODUCTS
48XBRMR120A Summary of contents
Page 1
... DC, 0.215A 48XBRMB120A 120V AC*, 0.108A 48XBRMG24D 24V DC, 0.215A 48XBRMG120A 120V AC*, 0.108A 48XBRMR24D 24V DC, 0.215A 48XBRMR120A 120V AC*, 0.108A 48XBRMW24D 24V DC, 0.215A 48XBRMW120A 120V AC*, 0.108A *120V AC 50/60 Hz Mechanical Specifications Outdoor Locations Temperature Ratings ........... -31F to +150F (-35C to +66C) http://www.edwardssignaling.com Phone: (800) 336-4206 Fax: (800) 454-2363 ...
Page 2
Locking Mechanism Power source Wires Figure 1. Conduit Mounting Top view of mounting base One of two knockouts for direct surface mounting Enclose in raceway To field wiring NOTE: Enclose wiring within an approved raceway interconnecting the appliance and junction ...
Page 3
Maintenance Cleaning CAUTION To prevent damage to the lens, do not use abrasive materials or cleaners. Periodically clean the lens surface with a soft cloth or sponge and water or a mild detergent solution to maintain optimum light visibility. Ensure ...
Page 4
U.S. T 800-336-4206 F 800-454-2363 Canada T 519 376 2430 F 519 376 7258 Asia T 852 2907 8108 F 852 2142 5063 Australia T +61 3 9239 1200 F +61 3 9239 1299 Europe 725 11 ...