D4GL4HFGA Omron, D4GL4HFGA Datasheet - Page 16

• Manufacturer Part Number: D4GL4HFGA
• Manufacturer: Omron
• Type: Safety-Door Switchr

Specifications of D4GL4HFGA

• Switch Function Configuration: N.C.
• Current Rating (max): 0.75A
• Operating Temp Range: -10C to 55C
• Lead Free Status / Rohs Status: Compliant

Wiring Precautions
Recommended Crimp Terminals
• Do not wire the Switch while power is being supplied. Doing so may
• Do not let particles, such as small pieces of lead wire, enter the
• Applicable lead wire size: AWG24 to AWG22 (0.2 to 0.3 mm
• Do not push crimp terminals into gaps in the case interior. Doing so
• Use crimp terminals that will not interfere with other components
J.S.T. Mfg Co.
• The terminal block screws and contact numbers correspond as
result in electric shock.
switch body when wiring.
Use lead wires of an appropriate length. Not doing so may result in
excess length causing the cover to rise and not fit properly.
may cause damage or deformation of the case.
inside the case.
shown in the following diagram. The numbers are provided on the
terminal cover. Confirm terminal numbers against the terminal
block terminal symbols when wiring.
E1
11
21
32
Manufacturer
O3 (Orange)
O1 (Green)
12
(Orange)
(Green)
LED
LED
FN0.5-3 (F Type)
No. 5-3 (Straight Type)
51
O2
(Black)
41
Solenoid
Model
42
52
22
31
E2
Safety
circuit
Auxiliary
circuit
Auxiliary
circuit
Auxiliary
circuit
2
).
Processing the Conduit Opening
Recommended Connectors
• Connect a recommended connector to the opening of the conduit
• When using a 1/2-14NPT conduit, wind sealing tape around the
• Make sure that the outer diameter of the cable connected to the
• Attach a conduit cap to the unused conduit opening when wiring
• Use a connector with a screw section not exceeding 10 mm.
• For a 1/2-14NPT conduit, use the above connector after attaching
Pg13.5
14NPT
and tighten the connector to the proper torque. The case may be
damaged if excessive tightening torque is applied.
conduit end of the connector so that the enclosure will conform to
IP67.
connector is correct.
and tighten it to a suitable torque. The conduit cap is provided with
the Switch.
Otherwise the screws will protrude into the case interior.
The connectors given in the following table have connectors with
screw sections not exceeding 10 mm.
Use the following connectors to ensure conformance to IP67.
Use LAPP connectors together with Seal Packing (JPK-16,
GP-13.5, or GPM20), and tighten to the applicable torque. Seal
Packing is sold separately.
• LAPP is a German manufacturer.
• OHM Electric Co. is a Japanese manufacturer.
the provided Adaptor to the Switch and wrapping it with sealing
tape.
Size
M20
G
1/2-
1
/
2
OHM ELECTRIC
Manufacturer
LAPP
LAPP
LAPP
LAPP
CO.
ST-PF1/2
5380-1002
OA-W1609
OA-W1611
S-13.5
5301-5030
ST-M20 × 1.5
5311-1020
ST-NPT1/2
5301-6030
Model
6.0 to 12.0 mm
9.0 to 11.0 mm
6.0 to 12.0 mm
7.0 to 13.0 mm
6.0 to 12.0 mm
7.0 to 9.0 mm
Applicable
diameter
cable
D4GL
16