GRM32ER61H106KA12L Murata, GRM32ER61H106KA12L Datasheet - Page 169

• Manufacturer Part Number: GRM32ER61H106KA12L
• Description: CAPACITOR, 1210, 10UF, 50V
• Manufacturer: Murata

Specifications of GRM32ER61H106KA12L

• Dielectric Characteristic: X5R
• Capacitance: 10µF
• Capacitance Tolerance: ± 10%
• Voltage Rating: 50V
• Capacitor Case Style: 1210
• Capacitor Mounting: SMD
• Operating Temperature Range: -55°C To +85°C
• Svhc: No SVHC
• Rohs Compliant: Yes

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
168
No.
10
* "Room condition" Temperature: 15 to 35 C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Medium Voltage High Capacitance for General Use Specifications and Test Methods
GRM Series Specifications and Test Methods
1
2
3
4
5
6
7
8
9
Operating
Temperature Range
Appearance
Dimensions
Dielectric Strength
Insulation Resistance
(I.R.)
Capacitance
Dissipation
Factor (D.F.)
Capacitance
Temperature
Characteristics
Adhesive Strength
of Termination
Vibration
Resistance
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance No defects or abnormalities
Capacitance Within the specified tolerance
D.F.
–55 to +125 C
No defects or abnormalities
Within the specified dimensions
No defects or abnormalities
CU0.01 F: More than 100M • F
CF0.01 F: More than 10,000M
Within the specified tolerance
0.025 max.
Cap. Change
Within 15%
(Temp. Range: –55 to +125 C)
No removal of the terminations or other defect should occur.
0.025 max.
Specifications
Visual inspection
Using calipers and micrometers
No failure should be observed when 150% of the rated voltage
(200% of the rated voltage in case of rated voltage: DC250V,
120% of the rated voltage in case of rated voltage: DC1kV) is
applied between the terminations for 1 to 5 sec., provided the
charge/discharge current is less than 50mA.
The insulation resistance should be measured with DC500 50V
(DC250 25V in case of rated voltage: DC250V) and within 60 5
sec. of charging.
The capacitance/D.F. should be measured at a frequency of
1 0.2kHz and a voltage of AC1 0.2V(r.m.s.)
The capacitance measurement should be made at each step
specified in the Table.
Solder the capacitor to the testing jig (glass epoxy board) shown
in Fig. 1.
Then apply 10N force in the direction of the arrow.
The soldering should be done using the reflow method and
should be conducted with care so that the soldering is uniform
and free of defects such as heat shock.
Solder the capacitor to the test jig (glass epoxy board).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should be
traversed in approximately 1 min. This motion should be applied
for a period of 2 hrs. in each of 3 mutually perpendicular
directions (total of 6 hrs.).
•Pretreatment
Perform a heat treatment at 150
let sit for 24 2 hrs. at room condition.*
Step
1
2
3
4
5
Glass Epoxy Board
Test Method
10N (5N : Size 1.6g0.8mm only), 10T1s
Glass Epoxy Board
Max. Operating Temp. 2
Min. Operating Temp. 3
Fig. 1
Continued on the following page.
–
Temperature ( C)
+0
–10
25 2
25 2
25 2
C for 60 5 min. and then
Solder resist
Cu
C02E.pdf
10.12.20