ISL83082EIU Intersil, ISL83082EIU Datasheet - Page 8

• Manufacturer Part Number: ISL83082EIU
• Description: IC TXRX RS485/422 5V ESD 8-MSOP
• Manufacturer: Intersil
• Type: Transceiverr

Specifications of ISL83082EIU

• Number Of Drivers/receivers: 1/1
• Protocol: RS422, RS485
• Voltage - Supply: 4.5 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Electrical Specifications
NOTES:
10. Transceivers are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 60ns, the parts are guaranteed
12. Set the RE signal high time >600ns to ensure that the device enters SHDN.
13. Does not apply to the ISL83084E.
14. Tested according to TIA/EIA-485-A, section 4.2.6 (±75V for 15µs at a 1% duty cycle).
15. Limits established by characterization and are not production tested.
11. Keep RE = VCC, and set the DE signal low time >600ns to ensure that the device enters SHDN.
Time to Shutdown
Receiver Enable from Shutdown to
Output High
Receiver Enable from Shutdown to
Output Low
RECEIVER SWITCHING CHARACTERISTICS (10Mbps Versions; ISL83086E, ISL83088E)
Maximum Data Rate
Receiver Input to Output Delay
Receiver Skew | t
Receiver Enable to Output Low
Receiver Enable to Output High
Receiver Disable from Output Low
Receiver Disable from Output High
Time to Shutdown
Receiver Enable from Shutdown to
Output High
Receiver Enable from Shutdown to
Output Low
4. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
5. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless
6. Supply current specification is valid for loaded drivers when DE = 0V.
7. Applies to peak current. See “Typical Performance Curves” beginning on page 12 for more information.
8. Keep RE = 0 to prevent the device from entering SHDN.
9. The RE signal high time must be short enough (typically <100ns) to prevent the device from entering SHDN.
and are not production tested.
otherwise specified.
not to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See “Low Power
Shutdown Mode” on page 12.
ISL83080E, ISL83082E, ISL83083E, ISL83084E, ISL83085E, ISL83086E, ISL83088E
PARAMETER
PLH
- t
PHL
|
8
Test Conditions: V
(Note 5). (Continued)
t
t
t
t
t
SYMBOL
ZH(SHDN)
PLH
ZH(SHDN)
ZL(SHDN)
ZL(SHDN)
t
t
SHDN
f
SHDN
t
MAX
SKD
t
t
t
t
ZH
HZ
ZL
LZ
, t
PHL
(Notes 10, 13)
R
(Notes 10, 12, 13)
R
(Notes 10, 12, 13)
(Figure 5) (Note 15)
(Figure 5)
(Figure 5)
R
(Note 9)
R
(Note 9)
R
R
(Note 10)
R
(Notes 10, 12)
R
(Notes 10, 12)
L
L
L
L
L
L
L
L
= 1kΩ, C
= 1kΩ, C
= 1kΩ, C
= 1kΩ, C
= 1kΩ, C
= 1kΩ, C
= 1kΩ, C
= 1kΩ, C
CC
= 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V
L
L
L
L
L
L
L
L
TEST CONDITIONS
= 15pF, SW = GND (Figure 6),
= 15pF, SW = V
= 15pF, SW = V
= 15pF, SW = GND (Figure 6)
= 15pF, SW = V
= 15pF, SW = GND (Figure 6)
= 15pF, SW = GND (Figure 6)
= 15pF, SW = V
CC
CC
CC
CC
(Figure 6),
(Figure 6)
(Figure 6)
(Figure 6)
TEMP
(°C)
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
(Note 4)
MIN
60
10
60
-
-
-
-
-
-
-
-
-
-
CC
TYP
160
150
150
160
150
150
15
70
10
10
10
10
0
= 5V, T
(Note 4)
A
MAX
2000
2000
2000
2000
600
125
600
10
30
30
30
30
= +25°C
-
April 22, 2008
FN6085.9
UNITS
Mbps
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns