B43514L0397M007 EPCOS Inc, B43514L0397M007 Datasheet

Page 1

... Aluminum electrolytic capacitors Capacitors with 4-pin snap-in terminals and solder pins Series/Type: B43514, B43524 Date: November 2008 © EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. ...

Page 2

... Many different case sizes Pinning ensures correct insertion RoHS-compatible Construction Charge/discharge-proof, polar Aluminum case, fully insulated with PVC Version with additional PET insulation cap on terminal side available for insulating the capacitor from the PCB (B43514 only) Overload protection by safety vent in case Terminals 4-pin snap-in terminals (6 ...

Page 3

... To IEC 60068-1: V 400 V DC: 40/105/ C/+105 C/56 days damp heat test > 400 V DC: 25/105/ C/+105 C/56 days damp heat test) R The capacitors can be operated in the temperature range +105 C but the impedance at consideration. Detail specification Similar to CECC 30301-808 Sectional specification IEC 60384-4 Please read Cautions and warnings and Important notes at the end of this document ...

Page 4

B43514, B43524 Extended temperature range Dimensional drawings B43514, 4-pin snap-in terminals, PVC insulation Standard snap-in terminals: length (6.3 1) mm. Also available with length of (4.5 All pin holes must be drilled into the PC-board, since the unconnected pins serve ...

Page 5

B43514, 4-pin snap-in terminals, PVC insulation and PET insulation cap on terminal side Standard snap-in terminals: length 6.3 +1/ 1.4 mm. Also available with length of 4.5 1.4 mm. PET insulation cap is positioned under the insulation sleeve. All pin ...

Page 6

B43514, B43524 Extended temperature range B43524, solder pins Pole markings: Plus: +; Minus: All pin holes must be drilled into the PC-board, since the unconnected pins serve as mountings. These pins must be soldered to isolated pads or pads with ...

Page 7

... Packing of 4-pin snap-in terminal and solder pin capacitors For ecological reasons the packing is pure cardboard. Ordering codes for terminal styles and insulation features Identification in 3rd block of ordering code 4-pin snap-in terminal capacitors Terminal version Standard terminals 6.3 mm Short terminals 4.5 mm Ordering examples: ...

Page 8

... The capacitance and voltage ratings listed above are available in different cases upon request. Other voltage and capacitance ratings are also available upon request. Capacitors with solder pins are only available in 35 and 40 mm case diameters. Please read Cautions and warnings and Important notes at the end of this document ...

Page 9

... Capacitors with solder pins are only available in 35 and 40 mm case diameters. Composition of ordering code * = Terminal type 1 = 4-pin snap-in terminals 2 = solder pin Please read Cautions and warnings and Important notes at the end of this document. Extended temperature range ...

Page 10

... Capacitors with solder pins are only available in 35 and 40 mm case diameters. Composition of ordering code * = Terminal type 1 = 4-pin snap-in terminals 2 = solder pin Please read Cautions and warnings and Important notes at the end of this document. 105 C ...

Page 11

... Capacitors with solder pins are only available in 35 and 40 mm case diameters. Composition of ordering code * = Terminal type 1 = 4-pin snap-in terminals 2 = solder pin Please read Cautions and warnings and Important notes at the end of this document. Extended temperature range ...

Page 12

B43514, B43524 Extended temperature range Useful life depending on ambient temperature T Frequency factor of permissible ripple current I versus frequency Refer to chapter "General technical information, 5.3 Calculation of useful life" on how to interpret the ...

Page 13

Impedance Z versus frequency f Typical behavior Please read Cautions and warnings and Important notes at the end of this document. B43514, B43524 Extended temperature range Page 105 C ...

Page 14

... However, the amount of dangerous materials used in our products has been limited to an absolute minimum. Nevertheless, the following rules should be observed when handling Al electrolytic capacitors: Any escaping electrolyte should not come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected parts immediately with running water ...

Page 15

... Please read Cautions and warnings and Important notes at the end of this document. B43514, B43524 Extended temperature range Page 105 C Reference Chapter "General technical information" 1 "Basic construction of aluminum electrolytic capacitors" 3.1.6 "Reverse voltage" 7.2 "Maximum permissible operating temperature" 10 "Maintenance" 11.1. "Mounting positions of capacitors with screw terminals" ...

Page 16

... B43514, B43524 Extended temperature range Topic Safety information Soldering, Do not allow halogenated hydrocarbons to come cleaning agents into contact with aluminum electrolytic capacitors. Passive Avoid external energy, such as fire or electricity. flammability Active Avoid overload of the capacitors. flammability Breakdown strength Do not damage the insulating sleeve, especially of insulating when ring clips are used for mounting ...

Page 17

Symbols and terms Symbol English C Capacitance C Rated capacitance R C Series capacitance S C Series capacitance at temperature T S,T C Capacitance at frequency Case diameter, nominal dimension d Maximum case diameter max ESL Self-inductance ...

Page 18

B43514, B43524 Extended temperature range Symbol English V Voltage V Forming voltage F V Operating voltage op V Rated voltage, DC voltage R V Surge voltage S X Capacitive reactance C X Inductive reactance L Z Impedance Z Impedance at ...

Page 19

Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical ...