LTC1565-31CS8 Linear Technology, LTC1565-31CS8 Datasheet
LTC1565-31CS8
Specifications of LTC1565-31CS8
Available stocks
Related parts for LTC1565-31CS8
LTC1565-31CS8 Summary of contents
Page 1
... Linear Phase Lowpass Filter DESCRIPTION The LTC ® phase lowpass fi lter. The selectivity of the LTC1565-31, combined with its linear phase and dynamic range, make it suitable for fi ltering in data communications or data acquisition systems. The fi lter attenuation is 36dB at 2× f ...
Page 2
... ABSOLUTE MAXIMUM RATINGS (Note 1) Total Supply Voltage ............................................... 11V Power Dissipation .............................................. 500mW Operating Temperature Range LTC1565-31CS8 ...................................... 0°C to 70°C LTC1565-31IS8 ................................... – 40°C to 85°C Storage Temperature Range ................. –65°C to 150°C Lead Temperature (Soldering, 10 sec) ................ 300°C ORDER INFORMATION LEAD FREE FINISH ...
Page 3
... G01 LTC1565-31 MIN TYP MAX 0.1 0.3 0.6 ±10 75 145 3 ±5 ±12 ±5 ±12 –400 –400 l 2.49 2.51 2.52 l 4 ...
Page 4
... LTC1565-31 TYPICAL PERFORMANCE CHARACTERISTICS Passband Gain vs Frequency Over Temperature 0 0.4 0.3 0.2 –40°C 0.1 85°C 0 25°C –0.1 –0.2 –0.3 –0.4 –0.5 25k 100k 400k FREQUENCY (Hz) 1565 G03 Common Mode Rejection Ratio 110 P 25°C 100 FREQUENCY (Hz) 1565 G06 PIN FUNCTIONS +IN, – ...
Page 5
... LTC1565-31 goes into the current saving shutdown mode. Pin 5 has a 4μA pull-up current. Leaving Pin 5 open will place the LTC1565-31 in its normal operating mode. – OUT, +OUT (Pins 7, 8): Output Pins. Pins 7 and 8 are the fi lter differential output. Each pin can drive 1kΩ or 300pF loads ...
Page 6
... LTC1565-31 APPLICATIONS INFORMATION Interfacing to the LTC1565-31 The difference between the voltages at Pin 1 and Pin 2 is the “differential input voltage.” The average of the voltages at Pin 1 and Pin 2 is the “common mode input voltage.” The difference between the voltages at Pin 7 and Pin 8 is the “ ...
Page 7
... THD versus output common mode voltage for a 2V mode input voltage that is 0.5V below mid supply. Figure 7. THD vs Common Mode Output Voltage 3.0 3.5 ) P-P 1565-31 F06 Figure 8. THD vs Common Mode Output Voltage LTC1565-31 differential input voltage and a common P 100kHz IN P-P V ...
Page 8
... SOURCE TO PROVIDE THE INPUT DC COMMON MODE VOLTAGE 0.1μF AMPLIFIERS A4 AND A5 ALLOW MONITORING/MEASURING THE DIFFERENTIAL OUTPUT WITH A SINGLE-ENDED, 6 GROUND-REFERENCED INSTRUMENT 0.1μ +IN +OUT 6 – –IN –OUT LTC1565- GND V 0.1μ – SHDN V 0.1μ TOTAL INTEGRATED NOISE 104μV RMS 118μV RMS = 650kHz CUTOFF TOTAL INTEGRATED NOISE • ...
Page 9
... LTC1565- GND 0.1μF 2.49k 4 5 – SHDN V NOTE: FOR SINGLE 5V SUPPLY CONNECTION, PIN 4 (LTC1565-31) AND PIN 4 (LT1809) SHOULD BE GROUNDED AND RESISTOR R2 SHOULD BE DC BIASED AT APPROXIMATELY 2.5V (SEE TEST CIRCUIT FOR SINGLE SUPPLY OPERATION +IN +OUT – –IN –OUT ...
Page 10
... DATA –IN 4.99k LTC1565-31 3 GND 0.1μF 4 – V Simple Pulse Shaping Circuit for Single 5V Operation, 2Mbps (1Msps) 4 Level Data 5V 4.99k 4.99k D1 1Msps 1 +IN DATA 10k 2 D0 –IN 4.99k LTC1565-31 3 GND 0.1μF 4 – +OUT OUT 7 – V –OUT OUT 0.1μF SHDN ...
Page 11
... TYP .016 – .050 .014 – .019 (0.406 – 1.270) (0.355 – 0.483) TYP INCHES (MILLIMETERS) LTC1565-31 ADC I DSP Q ADC 1565-31 TA03 .189 – .197 (4.801 – 5.004) NOTE ...
Page 12
... Frequency Response 0 –6 –12 –18 –24 –30 –36 –42 –48 100k 1M FREQUENCY (Hz) 1565 TA12 www.linear.com ● +IN +OUT OUT1 –IN –OUT OUT2 U2 LTC1565-31 FGND GND 0.1μF – SHDN 0.1μF V 15645-31 TA11 5V COMMENTS f = 500kHz or 1MHz CUTOFF f = 150kHz (LTC1562), CUTOFF(MAX 300kHz (LTC1562-2) CUTOFF(MAX) f ...