LTC1264CN Linear Technology, LTC1264CN Datasheet
LTC1264CN
Specifications of LTC1264CN
Available stocks
Related parts for LTC1264CN
LTC1264CN Summary of contents
Page 1
... Digital Communications ■ Spread Spectrum Communications ■ Spectral Analysis ■ Loran Receivers ■ Instrumentation , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. U TYPICAL APPLICATIO Clock-Tunable 8th Order Bandpass Filter, f 50k 50k IN INV B ...
Page 2
... V S ≥ ± ± < 2MHz CLK f < 2MHz CLK U W TOP VIEW ORDER PART 1 24 INV C NUMBER 2 23 HPC/ BPC 4 21 LPC LTC1264CN LTC1264CSW – CLK LPD 10 15 BPD 11 14 HPD/ INV D SW PACKAGE 24-LEAD PLASTIC SO (WIDE) = 110°C, θ = 65°C/W (N) ...
Page 3
ELECTRICAL C HARA TERISTICS C temperature range, otherwise specifications are unless otherwise noted. PARAMETER DC Offset Voltage (Note 3) Clock Feedthrough Maximum Clock Frequency Power Supply Current Note 1: Absolute Maximum Ratings are those values ...
Page 4
LTC1264 W U TYPICAL PERFOR A Typical Bandpass Gain Error vs Clock Frequency 5 MODE 25° ± ±7. 2.0 2.4 2.8 3.2 ...
Page 5
CTIO S + – (Pins 7, 19): Power Supply Pins. The V – the V (Pin 19) should each be bypassed with a 0.1µF capacitor to an adequate analog ground. The filter’s ...
Page 6
LTC1264 CTIO S CLK (Pin 18): Clock Input Pin. Any TTL or CMOS clock source with a square wave output and 50% duty cycle (±10 adequate clock source for the device. The power ...
Page 7
W ODES OF OPERATIO optimum mode for high Q designs with ratios greater than 20:1. CENTER Please refer to the Maximum Frequency of Operation paragraph under Applications Information for a guide to the use of capacitor C ...
Page 8
LTC1264 W ODES OF OPERATIO – V – Σ + 1/4 LTC1264 AGND √ CLK ...
Page 9
W ODES OF OPERATIO – AGND Figure 9. Mode 2n, 2nd Order Filter Providing a Lowpass Notch Output W BLOCK I D AGRA INV A 12 AGND 6 INV B 1 INV C ...
Page 10
LTC1264 PPLICATI S I FOR ATIO A Operating Limits The Typical Maximum Q vs Clock Frequency and Band- pass Gain Error graphs, under Typical Performance Char- acteristics, define an upper limit of operating Q for each LTC1264 ...
Page 11
PPLICATI S I FOR ATIO A For example, for an LTC1264 bandpass filter with f = 100kHz and f = 2MHz, a 3.9MHz, 10mV input will CLK produce a 100kHz, 10mV output. A 1st or 2nd order ...
Page 12
LTC1264 PPLICATI S I FOR ATIO INV B INV C R2 HPB/NB HPC/NC R3 STAGE 1 BPB BPC LPB LPC LTC1264 – AGND CLK SA ...
Page 13
O U TYPICAL A PPLICATI Linear Phase Clock-Tunable to 400kHz, Dual 4th Order Lowpass Filter INV B R2 HPB/NB R3 BPB R4 LPB C SB LTC1264 0.1µF AGND + LPA R3 ...
Page 14
LTC1264 O TYPICAL A PPLICATI 100kHz, 8th Order Notch Filter INV B INV C R2 HPB/NB HPC/NC R3 BPB BPC LPB LPC SB SC 0.1µF LTC1264 AGND V + 7.5V V CLK SA SD LPA LPD ...
Page 15
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... TA07a Passband Gain and Group Delay 3 124 0 114 GAIN –3 104 –6 94 –9 84 DELAY FREQUENCY (kHz) 1264 TA07c Noise per 2nd Order Section, Operation 3.3V to ±5V RMS LT/LT 0805 REV B • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 1993 1264fb ...