ATA8202-PXQW 19 Atmel, ATA8202-PXQW 19 Datasheet - Page 21

• Manufacturer Part Number: ATA8202-PXQW 19
• Description: IC RX UHF ASK/FSK 433MHZ 24-VQFN
• Manufacturer: Atmel
• Series: -r

Specifications of ATA8202-PXQW 19

• Frequency: 433MHz
• Sensitivity: -113dBm
• Data Rate - Maximum: 9.6 kbps
• Modulation Or Protocol: ASK, FSK
• Applications: AMR, ISM, Security and Access
• Current - Receiving: 6.7mA
• Data Interface: *
• Memory Size: *
• Antenna Connector: *
• Features: -
• Voltage - Supply: 2.7 V ~ 3.3 V, 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-VQFN Exposed Pad
• Pin Count: 24
• Screening Level: Industrial
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: ATA8202-PXQW

5. Power Supply
5.1
5.2
4971C–INDCO–04/09
OFF Mode
Standby Mode
Figure 5-1.
The supply voltage range of the ATA8201/ATA8202 is 2.7V to 3.3V or 4.5V to 5.5V.
Pin VS3V_AVCC is the supply voltage input for the range 2.7V to 3.3V, and is used in battery
applications using a single lithium 3V cell. Pin VS5V is the voltage input for the range 4.5V to
5.5V (car applications) in this case the voltage regulator V_REG regulates VS3V_AVCC to typi-
cally 3.0V. If the voltage regulator is active, a blocking capacitor of 2.2 µF has to be connected to
VS3V_AVCC (see
DVCC is the internal operating voltage of the digital control logic and is fed via the switch
SW_DVCC by VS3V_AVCC. DVCC must be blocked on pin DVCC with 68 nF (see
on page 28
Pin RX is the input to activate the RX signal processing and set the receiver to Active mode.
A low level on pin RX and ENABLE will set the receiver to OFF mode (low power mode). In this
mode, the crystal oscillator is shut down and no clock is available on pin CLK_OUT. The
receiver is not sensitive to a transmitter signal in this mode.
Table 5-1.
The receiver activates the Standby mode if pin ENABLE is set to “1”.
In Standby mode, the XTO is running and the clock on pin CLK_OUT is available after the
start-up time of the XTO ha s elapsed (dependent on pin CLK_OUT_CTRL0 an d
CLK_OUT_CTRL1). During Standby mode, the receiver is not sensitive to a transmitter signal.
In Standby mode, the RX signal path is disabled and the power consumption I
50 µA (CLK_OUT output off, VS3V_AVCC = VS5V = 3V). The exact value of this current is
strongly dependent on the application and the exact operation mode, therefore check the sec-
tion
VS3V_AVCC
“Electrical Characteristics: General” on page 30
VS5V
RX
RX
0
and
Power Supply
Standby Mode
Figure 10-1 on page
Figure 10-1 on page
ENABLE
IN
29).
0
29).
3.0V typ.
V_REG
EN
OUT
for the appropriate application case.
ATA8201/ATA8202
SW_DVCC
OFF mode
Function
Standby
Figure 9-1
is typically
DVCC
21