74AHC1G66GV,125 NXP Semiconductors, 74AHC1G66GV,125 Datasheet

IC SWITCH SPST SC74A

74AHC1G66GV,125

Manufacturer Part Number
74AHC1G66GV,125
Description
IC SWITCH SPST SC74A
Manufacturer
NXP Semiconductors
Series
74AHCr
Type
Analog Switchr
Datasheet

Specifications of 74AHC1G66GV,125

Package / Case
SC-74A, SOT-753
Function
Switch
Circuit
1 x SPST- NO
On-state Resistance
14 Ohm
Voltage Supply Source
Single Supply
Voltage - Supply, Single/dual (±)
2 V ~ 5.5 V
Current - Supply
1µA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Switch Configuration
SPST
On Resistance (max)
148 Ohm (Typ) @ 2 V
On Time (max)
35 ns @ 2 V
Off Time (max)
35 ns @ 2 V
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2 V
Maximum Power Dissipation
250 mW
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Package
5SOT-753
Maximum On Resistance
110@3.6V Ohm
Maximum Propagation Delay Bus To Bus
5@2V|2@3.6V|1@5.5V ns
Maximum Low Level Output Current
25 mA
Maximum Turn-on Time
35@2V ns
Switch Architecture
SPST
Power Supply Type
Single
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
74AHC1G66GV
74AHC1G66GV
935271669125
1. General description
2. Features
3. Ordering information
Table 1.
Type number
74AHC1G66GW
74AHCT1G66GW
74AHC1G66GV
74AHCT1G66GV
Ordering information
Package
Temperature range
74AHC1G66 and 74AHCT1G66 are high-speed Si-gate CMOS devices. They are
single-pole single-throw analog switches. The switch has two input/output pins (Y and Z)
and an active HIGH enable input pin (E). When pin E is LOW, the analog switch is turned
off.
I
I
I
I
I
I
I
40 C to +125 C
40 C to +125 C
74AHC1G66; 74AHCT1G66
Single-pole single-throw analog switch
Rev. 04 — 18 December 2008
Very low ON resistance:
High noise immunity
Low power dissipation
Balanced propagation delays
Multiple package options
ESD protection:
Specified from 40 C to +85 C and 40 C to +125 C
N
N
N
N
N
N
26
16
14
HMB JESD22-A114E exceeds 2000 V
MM JESD22-A115-A exceeds 200 V
CDM JESD22-C101C exceeds 1000 V
(typ.) at V
(typ.) at V
(typ.) at V
Name
TSSOP5
SC-74A
CC
CC
CC
= 3.0 V
= 4.5 V
= 5.5 V
Description
plastic thin shrink small outline package;
5 leads; body width 1.25 mm
plastic surface-mounted package; 5 leads
Product data sheet
Version
SOT353-1
SOT753

Related parts for 74AHC1G66GV,125

74AHC1G66GV,125 Summary of contents

Page 1

Single-pole single-throw analog switch Rev. 04 — 18 December 2008 1. General description 74AHC1G66 and 74AHCT1G66 are high-speed Si-gate CMOS devices. They are single-pole single-throw analog switches. The switch has two input/output pins (Y and Z) and an ...

Page 2

... NXP Semiconductors 4. Marking Table 2. Marking codes Type number 74AHC1G66GW 74AHCT1G66GW 74AHC1G66GV 74AHCT1G66GV 5. Functional diagram E Z 001aag487 Fig 1. Logic symbol 6. Pinning information 6.1 Pinning Fig 3. Pin configuration SOT353-1 and SOT753 74AHC_AHCT1G66_4 Product data sheet 74AHC1G66; 74AHCT1G66 Marking AL CL A66 C66 E Y Fig 2. Logic diagram ...

Page 3

... NXP Semiconductors 6.2 Pin description Table 3. Pin description Symbol Pin GND Functional description [1] Table 4. Function table Input [ HIGH voltage level LOW voltage level. 8. Limiting values Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). ...

Page 4

... NXP Semiconductors Table 6. Recommended operating conditions Voltages are referenced to GND (ground = 0 V). Symbol Parameter T ambient temperature amb t/ V input transition rise and fall rate [1] To avoid drawing V current out of pin Z, when switch current flows in pin Y, the voltage drop across the bidirectional switch must not CC exceed 0 the switch current fl ...

Page 5

... NXP Semiconductors Table 7. Static characteristics Voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions I OFF-state S(OFF) leakage see Figure 4 current I ON-state S(ON) leakage see Figure 5 current I supply current 5 additional per input pin supply current other inputs input E input I capacitance C ON-state input or output ...

Page 6

... NXP Semiconductors 10.2 ON resistance Table 8. ON resistance At recommended operating conditions; voltages are referenced to GND (ground 0 V); for graph see Symbol Parameter Conditions 74AHC1G66 and 74AHCT1G66 R ON resistance ON(peak) I (peak resistance V = GND; see ON(rail) I (rail [1] At supply voltages approaching 2 V, the analog switch ON resistance becomes extremely non-linear. Therefore it is recommended that these devices be used to transmit digital signals only, when using this supply voltage ...

Page 7

... NXP Semiconductors 11. Dynamic characteristics Table 9. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); C Symbol Parameter Conditions 74AHC1G66 t propagation see pd delay enable time see disable time see dis power V = GND dissipation capacitance 74AHCT1G66 t propagation see pd delay enable time see disable time see ...

Page 8

... NXP Semiconductors Table 9. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); C Symbol Parameter Conditions C power V = GND dissipation capacitance [1] All typical values are measured the same as t and PLH PHL t is the same as t and PZL PZH t is the same as t and t ...

Page 9

... NXP Semiconductors LOW-to-OFF OFF-to-LOW HIGH-to-OFF OFF-to-HIGH Measurement points are given in Logic levels: V and Fig 9. Enable and disable times Table 10. Measurement points Type Input V M 74AHC1G66 0.5V CC 74AHCT1G66 1.5 V 74AHC_AHCT1G66_4 Product data sheet 74AHC1G66; 74AHCT1G66 GND t PLZ V CC output PHZ output Y GND ...

Page 10

... NXP Semiconductors negative positive Test data is given in Table Definitions for test circuit Termination resistance should be equal to output impedance Load capacitance including jig and probe capacitance Load resistance Test selection switch. Fig 10. Test circuit for measuring switching times Table 11. Test data Type ...

Page 11

... NXP Semiconductors Table 12. Additional dynamic characteristics for 74AHC1G66 and 74AHCT1G66 GND = 3.0 ns pF; unless otherwise specified. All typical values are measured Symbol Parameter frequency ( 3dB) response isolation (OFF-state) iso [1] Adjust input voltage dBm level (0 dBm =1 mW into 11.3 Test circuits and graphs ...

Page 12

... NXP Semiconductors 4 (dB Test conditions 4.5 V; GND = Fig 13. Typical 3 dB frequency response Adjust the switch input voltage for a 0 dBm level (0 dBm = 1 mW into 600 ). Fig 14. Test circuit for measuring isolation (OFF-state) 74AHC_AHCT1G66_4 Product data sheet 74AHC1G66; 74AHCT1G66 SOURCE 0.1 F Y/Z ...

Page 13

... NXP Semiconductors 12. Package outline TSSOP5: plastic thin shrink small outline package; 5 leads; body width 1. DIMENSIONS (mm are the original dimensions UNIT max. 0.1 1.0 mm 1.1 0.15 0 0.8 Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION IEC SOT353-1 Fig 15 ...

Page 14

... NXP Semiconductors Plastic surface-mounted package; 5 leads DIMENSIONS (mm are the original dimensions) UNIT 0.100 0.40 1.1 0.26 mm 0.013 0.25 0.10 0.9 OUTLINE VERSION IEC SOT753 Fig 16. Package outline SOT753 (SC-74A) 74AHC_AHCT1G66_4 Product data sheet 74AHC1G66; 74AHCT1G66 scale 3.1 1.7 3.0 0.6 0.95 2 ...

Page 15

... Release date 74AHC_AHCT1G66_4 20081218 • Modifications: The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. • Legal texts have been adapted to the new company name where appropriate. • Package SOT353 changed to SOT353-1 in • ...

Page 16

... Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice ...

Page 17

... NXP Semiconductors 17. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 Ordering information . . . . . . . . . . . . . . . . . . . . . 1 4 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 6 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 7 Functional description . . . . . . . . . . . . . . . . . . . 3 8 Limiting values Recommended operating conditions Static characteristics 10.1 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 10.2 ON resistance . . . . . . . . . . . . . . . . . . . . . . . . . . 6 10.3 ON resistance test circuit and graphs Dynamic characteristics ...

Related keywords