ISL54205AIRZ-T Intersil, ISL54205AIRZ-T Datasheet
ISL54205AIRZ-T
Specifications of ISL54205AIRZ-T
Related parts for ISL54205AIRZ-T
ISL54205AIRZ-T Summary of contents
Page 1
... All other trademarks mentioned are the property of their respective owners. ISL54205A FN6342.1 Voltage on USB Cable BUS ) . . . . . . . . . . . . 2.7V to 3.6V DD μ TQFN and TDFN Packages μCONTROLLER USB HIGH-SPEED TRANSCEIVER CODEC | Intersil (and design registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2006. All Rights Reserved ...
Page 2
... Ordering Information TEMP. PART RANGE PART NUMBER MARKING (°C) - μTQFN ISL54205AIRUZ-T FT (Note) ISL54205AIRZ-T 205Z - TDFN (Note) ISL54205AIRZ 205Z - TDFN (Note) ISL54205EVAL1Z -40 to +85 Evaluation Board NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate or NiPdAu termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations ...
Page 3
... Maximum Junction Temperature (Plastic Package +150°C DD Maximum Storage Temperature Range -65°C to +150° 0.3V) DD Operating Conditions Temperature Range ISL54205AIRUZ and ISL54205AIRZ . . . . . . . . . . . . -40°C to +85°C exceeding V or GND by specified amount are clamped. Limit current to maximum current BUS DD Test Conditions ...
Page 4
Electrical Specifications - 2.7V to 3.6V Supply PARAMETER r Flatness FLAT(ON COMx OFF Leakage Current D+(OFF D-(OFF) COM float R ON Leakage Current ...
Page 5
Electrical Specifications - 2.7V to 3.6V Supply PARAMETER Input Current BUSH DD Input Current CTRLH DD V Pull-Down Resistor BUS VBUS DD CTRL Pull-Down Resistor CTRL DD NOTES Input ...
Page 6
Test Circuits and Waveforms V BUSH LOGIC INPUT V BUSL V OUT SWITCH OUTPUT 0V FIGURE 2A. MEASUREMENT POINTS /100mA ON 1 CTRL 100mA COMX GND Repeat test ...
Page 7
Test Circuits and Waveforms CTRL AUDIO OR USB IMPEDANCE ANALYZER COMx GND Repeat test for all switches. FIGURE 5. CAPACITANCE TEST CIRCUIT t ri 90% 50% 10% DIN+ t skew_i DIN- 90% 50% 10 90% 10% ...
Page 8
Application Block Diagram 22kΩ Detailed Description The ISL54205A device is a dual single pole/double throw (SPDT) analog switch device that operates from a single DC power supply in the range of 2.7V to 3.6V. It was designed to function as ...
Page 9
The USB switches are active (turned ON) whenever the ≥ V voltage 0.8V. V BUS DD BUS low, so when V is floating, the USB switches are OFF. BUS Note: Whenever the USB switches are ON ...
Page 10
Typical Performance Curves 0. 32Ω LOAD V = 0.707V LOAD RMS 0.10 0. 2.6V DD 0.08 0. 2. 0.05 0.04 20 200 FREQUENCY (Hz) FIGURE 8. THD+N vs ...
Page 11
Typical Performance Curves FIGURE 12. EYE PATTERN: 480Mbps WITH SWITCH IN THE SIGNAL PATH 11 ISL54205A T = +25°C, Unless Otherwise Specified (Continued) A TIME (10ns/DIV) FN6342.1 December 7, 2006 ...
Page 12
Typical Performance Curves 50Ω 0. P-P P-P 1M 10M FREQUENCY (Hz) FIGURE 13. FREQUENCY RESPONSE 12 ISL54205A T = +25°C, Unless Otherwise Specified (Continued) A Die ...
Page 13
... Maximum allowable burrs is 0.076mm in all directions. 9. Same as JEDEC MO-255UABD except: TERMINAL TIP No lead-pull-back, "A" MIN dimension = 0.45 not 0.50mm "L" MAX dimension = 0.45 not 0.42mm. 10. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB389. L MILLIMETERS MIN NOMINAL MAX A 0 ...
Page 14
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...