ISL54205AIRZ-T Intersil, ISL54205AIRZ-T Datasheet - Page 9

IC SWITCH MP3/USB2.0 HS 10-TDFN

ISL54205AIRZ-T

Manufacturer Part Number
ISL54205AIRZ-T
Description
IC SWITCH MP3/USB2.0 HS 10-TDFN
Manufacturer
Intersil
Datasheet

Specifications of ISL54205AIRZ-T

Function
USB Switch
Circuit
2 x SPDT
On-state Resistance
300 mOhm
Voltage Supply Source
Single Supply
Voltage - Supply, Single/dual (±)
2.7 V ~ 3.6 V
Current - Supply
6µA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
10-TDFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The USB switches are active (turned ON) whenever the
V
low, so when V
Note: Whenever the USB switches are ON the audio drivers
of the CODEC need to be at AC or DC ground or floating to
keep from interfering with the data transmission.
ISL54205A Operation
The discussion that follows will discuss using the ISL54205A
in the typical application shown in the block diagram on
page 8.
LOGIC CONTROL
The state of the ISL54205A device is determined by the
voltage at the VBUS pin (pin 2) and the CTRL pin (pin 10).
Refer to truth-table on page 2 of data sheet.
The VBUS pin and CTRL pin are internally pulled low
through 4M
CTRL control pin is only active when V
Logic control voltage levels:
V
Floating.
V
CTRL = Logic “0” (Low) when
CTRL = Logic “1” (High) when
Audio Mode
If the VBUS pin = Logic “0” and CTRL pin = Logic “1,” the
part will be in the Audio mode. In Audio mode the L (left) and
R (right) 3Ω audio switches are ON and the D- and D+ 5Ω
switches are OFF (high impedance). In a typical application,
V
connected to the battery or LDO of the MP3 player or cell
phone. When a headphone is plugged into the common
connector, nothing gets connected at the VBUS pin (it is
floating) and as long as the CTRL = Logic “1,” the
ISL54205A part remains in the audio mode and the audio
drivers of the player can drive the headphones and play
music.
USB Mode
If the VBUS pin = Logic “1” and CTRL pin = Logic “0” or
Logic “1,” the part will go into USB mode. In USB mode, the
D- and D+ 5Ω switches are ON and the L and R 3Ω audio
switches are OFF (high impedance). When a USB cable
from a computer or USB hub is connected at the common
connector, the voltage at the VBUS pin will be driven to be in
the range of 4.4V to 5.25V. The ISL54205A part will go into
the USB mode. In USB mode, the computer or USB hub
transceiver and the MP3 player or cell phone USB
transceiver are connected and digital data will be able to be
transmitted back and forth.
When the USB cable is disconnected, the ISL54205A
automatically turns the D+ and D- switches OFF.
BUS
BUS
BUS
DD
will be in the range of 2.7V to 3.6V and will be
voltage is
= Logic “0” (Low) when V
= Logic “1” (High) when V
Ω
resistors to ground and can be left floating. The
BUS
to V
is floating, the USB switches are OFF.
DD
+ 0.8V. V
9
BUS ≤
0.5V or floating.
BUS ≥
1.4V
BUS
V
V
BUS
is internally pulled
DD
DD
is logic “0”.
+ 0.8V
+ 0.2V or
ISL54205A
Low Power Mode
If the VBUS pin = Logic “0” and CTRL pin = Logic “0,” the
part will be in the Low Power mode. In the Low Power mode,
the audio switches and the USB switches are OFF (high
impedance). In this state, the device draws typically 1nA of
current.
EXTERNAL VBUS SERIES RESISTOR
The ISL54205A contains a clamp circuit between VBUS and
VDD. Whenever the VBUS voltage is greater than the VDD
voltage by more than 2.55V, current will flow through this
clamp circuitry into the V
During normal USB operation, V
3.6V and V
circuit is not active and no current will flow through the clamp
into the VDD supply.
In a USB application, the situation can exist where the V
voltage from the computer could be applied at the VBUS pin
before the V
range and current will flow through the clamp into the V
power supply bus. This current could be quite high when
V
components connected in the circuit. In the application
circuit, a 22k
pin to limit the current to a safe level during this situation.
It is recommended that a current limiting resistor in the range
of 10k
will have minimal impact on the logic level at the VBUS pin
during normal USB operation and protect the circuit during
the time VBUS is present before VDD is up to its normal
operating voltage.
Note: No external resistor is required in applications where
V
POWER
The power supply connected at VDD (pin 1) provides power
to the ISL54205A part. Its voltage should be kept in the
range of 2.7V to 3.6V when used in a USB/Audio application
to ensure you get proper switching when the V
at its lower limit of 4.4V.
DD
BUS
is OFF or at 0V and could potentially damage other
Ω
will not exceed V
to 50k
BUS
DD
Ω
Ω
resistor has been put in series with the VBUS
is in the range of 4.4V to 5.25V. The clamp
voltage is up to its normal operating voltage
be connected in series with the VBUS pin. It
DD
DD
by more than 2.55V.
power supply bus.
DD
is in the range of 2.7V to
BUS
December 7, 2006
voltage is
FN6342.1
DD
BUS

Related parts for ISL54205AIRZ-T