UPD43256BCZ-85L Renesas Electronics America, UPD43256BCZ-85L Datasheet
UPD43256BCZ-85L
Specifications of UPD43256BCZ-85L
Available stocks
Related parts for UPD43256BCZ-85L
UPD43256BCZ-85L Summary of contents
Page 1
Description μ The PD43256B is a high speed, low power, and 262,144 bits (32,768 words by 8 bits) CMOS static RAM. Battery backup is available. And A and B versions are wide voltage operations. μ The PD43256B is packed in ...
Page 2
Ordering Information Part number Package μ PD43256BCZ-70L 28-pin PLASTIC DIP μ PD43256BCZ-85L (15.24 mm (600)) μ PD43256BCZ-70LL μ PD43256BCZ-85LL μ PD43256BGU-70L 28-pin PLASTIC SOP μ PD43256BGU-85L (11.43 mm (450)) μ PD43256BGU-70LL μ PD43256BGU-85LL μ PD43256BGU-A85 μ PD43256BGU-A10 μ PD43256BGU-A12 μ ...
Page 3
Pin Configurations (Marking Side) /xxx indicates active low signal. 28-pin PLASTIC DIP (15.24 mm (600)) A14 A12 I/O1 I/O2 I/O3 GND Remark Refer to Package Drawings for the 1-pin index mark. μ ...
Page 4
A14 A12 I/O1 I/O2 I/O3 GND Remark Refer to Package Drawings for the 1-pin index mark. 4 28-pin PLASTIC SOP (11.43 mm (450)) μ [ PD43256BGU-xxL ] μ [ PD43256BGU-xxLL ] μ ...
Page 5
PLASTIC TSOP (I) (8x13.4) (Normal bent) μ [ PD43256BGW-xxLL-9JL ] μ [ PD43256BGW-Axx-9JL ] μ [ PD43256BGW-Bxx-9JL ] μ [ PD43256BGW-xxLL-9JL-A ] μ [ PD43256BGW-Axx-9JL-A ] μ [ PD43256BGW-Bxx-9JL-A ] /OE 1 A11 A13 ...
Page 6
Block Diagram A0 Address buffer A14 I/O1 I/O8 /CS /OE / GND Truth Table /CS /OE /WE × × × Remark × ...
Page 7
Electrical Specifications Absolute Maximum Ratings Parameter Symbol Supply voltage Input / Output voltage Operating ambient temperature Storage temperature Note –3.0 V (MIN.) (Pulse width : 50 ns) Caution Exposing the device to stress above those listed in Absolute Maximum Rating ...
Page 8
DC Characteristics (Recommended Operating Conditions Unless Otherwise Noted) (1/2) Parameter Symbol Input leakage current I/O leakage current I/O / Operating supply ...
Page 9
DC Characteristics (Recommended Operating Conditions Unless Otherwise Noted) (2/2) Parameter Symbol Input leakage current I/O leakage current I/O / Operating ...
Page 10
AC Characteristics (Recommended Operating Conditions Unless Otherwise Noted) AC Test Conditions μ μ [ PD43256B-70L, PD43256B-85L, Input Waveform (Rise and Fall Time ≤ 5 ns) 2.2 V 1.5 V 0.8 V Output Waveform Output Load AC characteristics should be measured ...
Page 11
Read Cycle (1/2) Parameter Symbol Read cycle time t RC Address access time t AA /CS access time t ACS /OE access time t OE Output hold from address change t OH /CS to output in low impedance t CLZ ...
Page 12
Read Cycle Timing Chart Address (Input) /CS (Input) /OE (Input) I/O (Output) Remark In read cycle, /WE should be fixed to high level ACS t CLZ OLZ High impedance Data Sheet ...
Page 13
Write Cycle (1/2) Parameter Symbol Write cycle time t WC /CS to end of write t CW Address valid to end of write t AW Write pulse width t WP Data valid to end of write t DW Data hold ...
Page 14
Write Cycle Timing Chart 1 (/WE Controlled) Address (Input) /CS (Input /WE (Input) I/O (Input / Output) Indefinite data out Cautions 1. /CS or /WE should be fixed to high level during address transition. 2. When I/O pins ...
Page 15
Write Cycle Timing Chart 2 (/CS Controlled) Address (Input) /CS (Input) /WE (Input) High impedance I/O (Input) Cautions 1. /CS or /WE should be fixed to high level during address transition. 2. When I/O pins are in the output state, ...
Page 16
Low V Data Retention Characteristics (T CC Parameter Symbol Data retention supply voltage V CCDR Data retention supply current I CCDR Chip deselection t CDR to data retention mode Operation recovery time t R μ 40 °C) Notes 1. 3 ...
Page 17
Package Drawings 28-PIN PLASTIC DIP (15.24 mm (600 NOTES 1. Each lead centerline is located within 0. its true position (T.P.) at maximum material condition. 2. Item "K" ...
Page 18
PLASTIC SOP (11.43 mm (450 NOTE Each lead centerline is located within 0. its true position (T.P.) at maximum material condition ...
Page 19
PLASTIC TSOP(I) (8x13. NOTES 1. Each lead centerline is located within 0. its true position (T.P.) at maximum material condition. 2. "A" excludes mold flash. (Includes mold flash : 8.4mm ...
Page 20
Recommended Soldering Conditions Please consult with our sales offices for soldering conditions of the Types of Surface Mount Device μ PD43256BGU-xxL : 28-pin PLASTIC SOP (11.43 mm (450)) μ PD43256BGU-xxLL : 28-pin PLASTIC SOP (11.43 mm (450)) μ PD43256BGU-Axx : ...
Page 21
Revision History Edition/ Page Date This Previous edition edition 15th edition/ through through Nov. 2008 Type of Description revision Modification Ordering Information revised. Data Sheet M10770EJFV0DS μ PD43256B 21 ...
Page 22
MEMO ] 22 Data Sheet M10770EJFV0DS μ PD43256B ...
Page 23
NOTES FOR CMOS DEVICES 1 VOLTAGE APPLICATION WAVEFORM AT INPUT PIN Waveform distortion due to input noise or a reflected wave may cause malfunction. If the input of the CMOS device stays in the area between V malfunction. Take care ...
Page 24
The information in this document is current as of November, 2008. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most ...