MC68HC11E0CFN3 Freescale Semiconductor, MC68HC11E0CFN3 Datasheet - Page 81

MC68HC11E0CFN3

Manufacturer Part Number
MC68HC11E0CFN3
Description
Manufacturer
Freescale Semiconductor
Datasheet

Specifications of MC68HC11E0CFN3

Cpu Family
HC11
Device Core Size
8b
Frequency (max)
3MHz
Interface Type
SCI/SPI
Program Memory Type
ROMLess
Program Memory Size
Not Required
Total Internal Ram Size
512Byte
# I/os (max)
38
Number Of Timers - General Purpose
8
Operating Supply Voltage (typ)
3.3/5V
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
3V
On-chip Adc
8-chx8-bit
Instruction Set Architecture
CISC
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
52
Package Type
PLCC
Lead Free Status / Rohs Status
Not Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC68HC11E0CFN3
Manufacturer:
MOT
Quantity:
119
Part Number:
MC68HC11E0CFN3
0
Part Number:
MC68HC11E0CFN3R2
Manufacturer:
FREESCALE
Quantity:
1 831
Part Number:
MC68HC11E0CFN3R2
Manufacturer:
MOTOROLA
Quantity:
12 234
Complete this 2-step reset sequence to service the COP timer:
Performing instructions between these two steps is possible as long
as both steps are completed in the correct sequence before the timer times out.
5.2.4 Clock Monitor Reset
The clock monitor circuit is based on an internal resistor capacitor (RC) time delay. If no MCU clock edges
are detected within this RC time delay, the clock monitor can optionally generate a system reset. The
clock monitor function is enabled or disabled by the CME control bit in the OPTION register. The presence
of a timeout is determined by the RC delay, which allows the clock monitor to operate without any MCU
clocks.
Clock monitor is used as a backup for the COP system. Because the COP needs a clock to function, it is
disabled when the clock stops. Therefore, the clock monitor system can detect clock failures not detected
by the COP system.
Semiconductor wafer processing causes variations of the RC timeout values between individual devices.
An E-clock frequency below 10 kHz is detected as a clock monitor error. An E-clock frequency of 200 kHz
or more prevents clock monitor errors. Using the clock monitor function when the E-clock is below 200
kHz is not recommended.
Special considerations are needed when a STOP instruction is executed and the clock monitor is enabled.
Because the STOP function causes the clocks to be halted, the clock monitor function generates a reset
sequence if it is enabled at the time the stop mode was initiated. Before executing a STOP instruction,
clear the CME bit in the OPTION register to 0 to disable the clock monitor. After recovery from STOP, set
the CME bit to logic 1 to enable the clock monitor. Alternatively, executing a STOP instruction with the
CME bit set to logic 1 can be used as a software initiated reset.
Freescale Semiconductor
1. Write $55 to COPRST to arm the COP timer clearing mechanism.
2. Write $AA to COPRST to clear the COP timer.
Address
Reset:
Read:
Write:
Figure 5-1. Arm/Reset COP Timer Circuitry Register (COPRST)
$103A
BIT 7
Bit 7
0
BIT 6
0
6
M68HC11E Family Data Sheet, Rev. 5.1
BIT 5
5
0
BIT 4
4
0
BIT 3
3
0
BIT 2
2
0
BIT 1
1
0
BIT 0
Bit 0
0
Resets
81

Related parts for MC68HC11E0CFN3